Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco 3750G all links reset

I have a Cisco 3750G with routing enabled. Sometimes, I experience a situation: some clients computers are disconnected from the switch and then reconnected immediately. The whole things happened and ended within 5s. But it often happened, >5 times a day.

The log in switch shows:

Switch#sh log

Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)

No Active Message Discriminator.

No Inactive Message Discriminator.

    Console logging: level debugging, 373 messages logged, xml disabled,

                     filtering disabled

    Monitor logging: level debugging, 0 messages logged, xml disabled,

                     filtering disabled

    Buffer logging:  level debugging, 373 messages logged, xml disabled,

                     filtering disabled

    Exception Logging: size (4096 bytes)

    Count and timestamp logging messages: disabled

    File logging: disabled

    Persistent logging: disabled

No active filter modules.

    Trap logging: level informational, 377 message lines logged

Log Buffer (4096 bytes):

rface GigabitEthernet1/0/13, changed state to down

1d21h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

1d21h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down

2d02h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up

2d02h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up

Switch#


I didn't see any problems here, just some interfaces are down and then become up again. This happened not only on this single computer, but on some other devices including a Apple Airport Exterem.

Anyone has any idea about this?

Thanks in advanced.

UPDATE @ Feb 14 20:05 NST:

Configuration on that port is listed below:

Switch#sh run int gi1/0/13

Building configuration...

Current configuration : 66 bytes

!

interface GigabitEthernet1/0/13

switchport access vlan 30

end

Switch#sh int gi1/0/13

GigabitEthernet1/0/13 is up, line protocol is up (connected)

  Hardware is Gigabit Ethernet, address is 0014.a93b.830d (bia 0014.a93b.830d)

  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

  Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX

  input flow-control is off, output flow-control is unsupported

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input 00:13:27, output 00:00:01, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 14000 bits/sec, 7 packets/sec

  5 minute output rate 175000 bits/sec, 8 packets/sec

     802083047 packets input, 1214885172159 bytes, 0 no buffer

     Received 34405 broadcasts (16832 multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 watchdog, 16832 multicast, 0 pause input

     0 input packets with dribble condition detected

     810796080 packets output, 62243896017 bytes, 0 underruns

     0 output errors, 0 collisions, 2 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier, 0 PAUSE output

     0 output buffer failures, 0 output buffers swapped out

Switch#sh hard

Cisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE8, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Wed 26-Jun-13 11:25 by prod_rel_team

Image text-base: 0x01000000, data-base: 0x02F00000

ROM: Bootstrap program is C3750 boot loader

BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)

Switch uptime is 4 days, 1 hour, 52 minutes

System returned to ROM by power-on

System image file is "flash:c3750-ipservicesk9-mz.122-55.SE8/c3750-ipservicesk9-mz.122-55.SE8.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

Switch#sh ver

Cisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE8, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Wed 26-Jun-13 11:25 by prod_rel_team

Image text-base: 0x01000000, data-base: 0x02F00000

ROM: Bootstrap program is C3750 boot loader

BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)

Switch uptime is 4 days, 1 hour, 52 minutes

System returned to ROM by power-on

System image file is "flash:c3750-ipservicesk9-mz.122-55.SE8/c3750-ipservicesk9-mz.122-55.SE8.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco WS-C3750G-24T (PowerPC405) processor (revision J0) with 131072K bytes of memory.

Processor board ID CAT0929Z31B

Last reset from power-on

5 Virtual Ethernet interfaces

24 Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : 00:14:A9:3B:83:00

Motherboard assembly number     : 73-8046-08

Power supply part number        : 341-0048-03

Motherboard serial number       : CAT09300BFA

Power supply serial number      : DTH09262K40

Model revision number           : J0

Motherboard revision number     : B0

Model number                    : WS-C3750G-24T-S

System serial number            : CAT0929Z31B

Hardware Board Revision Number  : 0x05

Switch Ports Model              SW Version            SW Image

------ ----- -----              ----------            ----------

*    1 24    WS-C3750G-24T      12.2(55)SE8           C3750-IPSERVICESK9-M

Configuration register is 0xF

Switch#



UPDATE @ Feb 14 20:45 NST

Switch#sh controller e GigabitEthernet1/0/13

     Transmit GigabitEthernet1/0/13           Receive

   2153682004 Bytes                       3714795707 Bytes

    810677366 Unicast frames               802082816 Unicast frames

       149673 Multicast frames                 17023 Multicast frames

        18389 Broadcast frames                 17786 Broadcast frames

            0 Too old frames              3709393103 Unicast bytes

            0 Deferred frames                2881529 Multicast bytes

            0 MTU exceeded frames            2521075 Broadcast bytes

            0 1 collision frames                   0 Alignment errors

            0 2 collision frames                   0 FCS errors

            0 3 collision frames                   0 Oversize frames

            0 4 collision frames                   0 Undersize frames

            0 5 collision frames                   0 Collision fragments

            0 6 collision frames

            0 7 collision frames             1320039 Minimum size frames

            0 8 collision frames              250602 65 to 127 byte frames

            0 9 collision frames              165765 128 to 255 byte frames

            0 10 collision frames              77695 256 to 511 byte frames

            0 11 collision frames             124005 512 to 1023 byte frames

            0 12 collision frames          800179519 1024 to 1518 byte frames

            0 13 collision frames                  0 Overrun frames

            0 14 collision frames                  0 Pause frames

            0 15 collision frames

            0 Excessive collisions                 0 Symbol error frames

            0 Late collisions                      0 Invalid frames, too large

            0 VLAN discard frames                  0 Valid frames, too large

            0 Excess defer frames                  0 Invalid frames, too small

    802135613 64 byte frames                       0 Valid frames, too small

       243436 127 byte frames

      1271533 255 byte frames                      0 Too old frames

       100832 511 byte frames                      0 Valid oversize frames

        64915 1023 byte frames                     0 System FCS error frames

      7029099 1518 byte frames                     0 RxPortFifoFull drop frame

            0 Too large frames

            0 Good (1 coll) frames

            0 Good (>1 coll) frames

Switch#

UPDATE @ Feb 14 21:25 NST

Switch#test cable tdr interface G 1/0/13

TDR test started on interface Gi1/0/13

A TDR test can take a few seconds to run on an interface

Use 'show cable-diagnostics tdr' to read the TDR results.

Switch#sh cable tdr interface G 1/0/13

TDR test last run on: March 05 03:07:45

Interface Speed Local pair Pair length        Remote pair Pair status

--------- ----- ---------- ------------------ ----------- --------------------

Gi1/0/13  1000M Pair A     2    +/- 10 meters Pair B      Normal

                Pair B     0    +/- 10 meters Pair A      Normal

                Pair C     0    +/- 10 meters Pair D      Normal

                Pair D     0    +/- 10 meters Pair C      Normal

Switch#


UPDATE @ 14:30 Feb 17 NST

Switch#test cable-diagnostics tdr interface G 1/0/15

TDR test started on interface Gi1/0/15

A TDR test can take a few seconds to run on an interface

Use 'show cable-diagnostics tdr' to read the TDR results.

Switch#show cable-diagnostics tdr int G 1/0/13

TDR test last run on: March 05 03:07:45

Interface Speed Local pair Pair length        Remote pair Pair status

--------- ----- ---------- ------------------ ----------- --------------------

Gi1/0/13  1000M Pair A     2    +/- 10 meters Pair B      Normal

                Pair B     0    +/- 10 meters Pair A      Normal

                Pair C     0    +/- 10 meters Pair D      Normal

                Pair D     0    +/- 10 meters Pair C      Normal

Switch#


Regards, Lingfeng Xiong
Everyone's tags (1)
13 REPLIES
Silver

Cisco 3750G all links reset

Hi,

What is the running config if those interfaces

show us the output of :

Show run int x/y

show int x/y

Add 'spanning tree portfast' to the interfaces where you have computers connected.

Thanks

Ankur

"Please rate the post if found useful"

New Member

Cisco 3750G all links reset

Hi,

I updated my original post to contain the information you requested.

Thank you.

Regards, Lingfeng Xiong
New Member

Re: Cisco 3750G all links reset

Hi. The output has been updated to original post.

I didn't add 'spanning tree portfast' to any interface. Every time the computer disconnected, it resume it's connection within 5 seconds, and the port LED in switch keep showing Green. I believe the port does not enter 'down -> blocking -> learning -> forwarding' cycle in this case.

Regards,
Lingfeng Xiong

Regards, Lingfeng Xiong

Cisco 3750G all links reset

  Hi,

i encountered the same your problem on our customer network. Sometimes all uplink freeze and after 5 - 10 seconds replaces itself.

Our platform: 3 x WS-C3750G-24TS-1U stacked:

Software version and image:

12.2(35)SE5             C3750-IPBASE-M

Can you share yours?

Thanks

Pier

New Member

Re: Cisco 3750G all links reset

Hi.

I believe this problem does not occurred before I enable the routing function.

The information you requested has been contained in my original question, I updated it :-) (Only one standalone switch. No stacking)

Thank you.

Regards, Lingfeng Xiong
Hall of Fame Super Gold

Cisco 3750G all links reset

Post the output to the command "sh controller e GigabitEthernet1/0/13".

New Member

Cisco 3750G all links reset

Hi,

Information updated at original post.

Regards, Lingfeng Xiong
Hall of Fame Super Gold

Cisco 3750G all links reset

Ok, no line errors detected for a switch uptime of four (4+) days. 

Do this:

1.  Command:  test cable tdr interface G 1/0/13;

2.  Wait for 7 seconds;

3.  Command:  sh cable tdr interface G 1/0/13; and

4.  Post the output to #3 BELOW. 

New Member

Re: Cisco 3750G all links reset

I updated my original post to contains complete output of those two commands.

BTW: I recalled this problem does not exist before I enable the routing function of this switch.

I have no idea if this is a coincident or not. Because this switch is currently used in a production environment, I cannot turn routing down for testing.

Regards, Lingfeng Xiong
Hall of Fame Super Gold

Re: Cisco 3750G all links reset

There's nothing wrong with the cable.  There's no line errors. 

I'm looking at possibly the drivers of your network card could be an issue.

New Member

Re: Cisco 3750G all links reset

Hi.

I'm pretty sure that the NIC and driver is not the problem. This is because:

1. before connecting to this switch, this computer has been connected to other switches without any problem

2. the operating system has been reinstalled but problem still there

and

3. another Apple Airport Extreme which connected to this switch also experiencing this problem.

Thanks

Regards, Lingfeng Xiong
Hall of Fame Super Gold

Re: Cisco 3750G all links reset

I'm pretty sure that the NIC and driver is not the problem.

Back in 2008, I had witnessed first-hand on how a brand new Intel GigabitEthernet NIC card reacts to legacy 3500XL switches.  No matter what IOS you've loaded on the switch the links will go down/up between 25 to 45 times per minute.  This will cause users very, very slow response.  The easiest way to fix this issue is to force the NIC card to negotiate to 100/Full. 

I am not saying to you have Intel NIC card but so far all suspects are on the table.  Your wired NIC card has not been ruled out. 

another Apple Airport Extreme which connected to this switch also experiencing this problem.

Hmmmm ... I'm reviewing the TDR result.  What kind of cable is this?  Is this a 1 metre cable?  Can you please change this?

New Member

Re: Cisco 3750G all links reset

Hi,

It is a one metre cable with text "Cat 5e PATCH --- UTP".

I'll try to replace it and see what happened.

PS: Althouth it's not a cat 6 cable, it works great when transferring files. The speed can exceed 105MB/s :-)

Regards,
Lingfeng Xiong

P.S.: I just updated the original post with Airport Exterme's port test result (Gi 1/0/15)

P.S.: gi 1/0/13 and gi 1/0/15 are different cables.

Regards, Lingfeng Xiong
808
Views
0
Helpful
13
Replies