Cisco 3750G Post Failure: Anyone know if this looks like HW or SW issue?
Thanks in advance for any advice or input. I recently acquired a Cisco 3750G-48PS-S switch for a CCNA lab I am putting together. In console, when the switch boots I get the following failure/error. Wondering if anyone has seen this before and if it points to a hardware or software issue?
File "flash:c3750-ipbase-mz.122-25.SEB4/c3750-ipbase-mz.122-25.SEB4.bin" uncompressed and installed, entry point: 0x3000 executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, C3750 Software (C3750-IPBASE-M), Version 12.2(25)SEB4, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Tue 30-Aug-05 15:47 by yenanh Image text-base: 0x00003000, data-base: 0x00C72590
front_end/ (directory) extracting front_end/fe_type_1 (34696 bytes) extracting front_end/front_end_ucode_info (43 bytes) extracting ucode_info (76 bytes) POST: CPU MIC register Tests : Begin POST: CPU MIC register Tests : End, Status Passed
POST: PortASIC Memory Tests : Begin POST: PortASIC Memory Tests : End, Status Passed
POST: CPU MIC PortASIC interface Loopback Tests : Begin POST: CPU MIC PortASIC interface Loopback Tests : End, Status Passed
POST: PortASIC RingLoopback Tests : Begin POST: PortASIC RingLoopback Tests : End, Status Passed
Waiting for Stack Master Election (around 30 seconds)... POST: PortASIC CAM Subsystem Tests : Begin HTD POST: Basic Test Failed POST: POST Failed POST: PortASIC CAM Subsystem Tests : End, Status Failed
POST: CAM test failed POST Failed: disabling stack links and shutting down SDP
driver class subsystem initialization failed
cisco WS-C3750G-48PS (PowerPC405) processor (revision J0) with 118784K/12280K bytes of memory. Processor board ID FOC1252W69Z Last reset from power-on The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00:1C:F6:0B:FF:80 Motherboard assembly number : 73-9365-08 Power supply part number : 341-0108-01 Motherboard serial number : FOC09483L58 Power supply serial number : PAJ08490090 Model revision number : J0 Motherboard revision number : A0 Model number : WS-C3750G-48PS-S System serial number : FOC1252W69Z Top Assembly Part Number : 800-26857-02 Top Assembly Revision Number : A0 Version ID : V03 CLEI Code Number : CNMWN00ARB Hardware Board Revision Number : 0x09
!!! WARNING: The switch is not usable !!! Unable to create l2trace server process, socket_open() failed
Press RETURN to get started!
00:00:46: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlanCannot Get the number of ports in MAC notification
00:00:47: %SW_VLAN-4-IFS_FAILURE: VLAN manager encountered file operation error: call = ifs_read_until (header) / file = / code = 21 (Is a directory) / bytes transfered = -1 -Traceback= 8A4200 190598 18CA50 7599A8 753BEC 00:00:48: %SYS-5-RESTART: System restarted -- Cisco IOS Software, C3750 Software (C3750-IPBASE-M), Version 12.2(25)SEB4, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Tue 30-Aug-05 15:47 by yenanh 00:00:48: Unable to open UDP socket on CMP_PORT
Question We run asr9001 with XR 6.1.3, and we have a very long delay to
login w/ SSH 1 or 2 to the device compare to IOS device. After
investigation, the there is 1s delay between the client KEXDH_INIT and
the server (XR) KEXDH_REPLY. After debug ssh serv...
Introduction The purpose of this document is to demonstrate the Open
Shortest Path First (OSPF) behavior when the V-bit (Virtual-link bit) is
present in a non-backbone area. The V-bit is signaled in Type-1 LSA only
if the router is the endpoint of one or ...
Hi, I am seeing quite a few issues with patch install and wanted to
share my experience and workaround to this. Login to admin via CLI, then
access root with the “shell” command Issue “df –h” and you’ll probably
see the following directory full or nearly ...