11-24-2013 06:50 AM - edited 03-07-2019 04:45 PM
Dear All,
I have small question, I am planning for Cisco 3750X with 10G SFP+ service module. I want to know that whether it can be used as Access Ports connecting to server as this is mostly used as uplink port.
Thank You,
Abhisar.
Solved! Go to Solution.
11-24-2013 06:55 AM
you can connect whatever you want as long as the connected system supports the same medium/standard.
11-24-2013 06:59 AM
Hi,
See this:
The C3KX-NM-10GT 10-Gigabit Ethernet Network Module has two 10-Gigabit Ethernet copper port that can operate at either 1 Gigabit per second or 10 Gigabits per second. To configure the port speed to 1 Gigabit per second, use the hw-module switch global configuration command. See the command reference for command syntax description.
Note 10 Mb/s and 100 Mb/s speeds are not supported on this module.
That said it should work as an access port as long as you follow those guide lines.
Regards,
11-24-2013 06:55 AM
you can connect whatever you want as long as the connected system supports the same medium/standard.
11-24-2013 06:59 AM
Hi,
See this:
The C3KX-NM-10GT 10-Gigabit Ethernet Network Module has two 10-Gigabit Ethernet copper port that can operate at either 1 Gigabit per second or 10 Gigabits per second. To configure the port speed to 1 Gigabit per second, use the hw-module switch global configuration command. See the command reference for command syntax description.
Note 10 Mb/s and 100 Mb/s speeds are not supported on this module.
That said it should work as an access port as long as you follow those guide lines.
Regards,
11-24-2013 07:09 AM
Dear Karsten/Leo,
Thank you for your promt response.
I will be going for C3KX-NM-10G which has 2*10G SFP+ and 2*1G SFP and connecting two servers having 10G optical card.
Thank you again
Thank You,
Abhisar.
11-25-2013 03:17 AM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Well if you want to connect anything with 10g to a 3750X, you're limited to using a module with 10g ports.
Other than 10g capability on some module cards, something to note, the module ports, I believe, are supported by larger buffers (including the gig module ports).
As the others have noted, you can use any port for any purpose. However, if you connect a server to a 10g port, be aware you might start to see drops on your other host (gig) ports as the server will now be able send faster than the host port can receive data. To minimize this, you might either disable QoS on the switch (providing maximum buffers to all egress traffic) or you might need to tweak buffer resource settings (the default settings often drop some packets, when there are bursts, of default marked packets).
11-29-2013 08:34 AM
Dear Joesph,
Thank you for your reply.
We are not doing any QOS in network, we will be focousing on communication between two servers(5 VMs on each) having 10G connectivity connected to switch.
Also can you share any doc or commands to tune buffer resource to avoide any packet drops.
Thank You,
Abhisar.
11-29-2013 05:45 PM
Also can you share any doc or commands to tune buffer resource to avoide any packet drops.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide