Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Cisco 6500 PPPoE

Need to setup 6500 as pppoe server, I am not seeing commands I have on other platforms such as ( bba-group , vpdn-group )

Whats needs to be done to use a 6500 as a pppoe server?

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Re: Cisco 6500 PPPoE

Hello Dan,

it looks like your C6500 has a supervisor 2 installed from the image name that appears in show ver.

if so MPLS requires specialized linecards like OSM or WAN gigabit interfaces.

AToM (Any Transport over MPLS) could be of help allowing you to send the PPP sessions to some other device but it is not possible at the moment if you haven't at least a sup 720 3BXL.

I would have been surprised to see PPPoE supported on this platform. If you have a C7200 VXR it can be a valid solution.

Hope to help

Giuseppe

11 REPLIES
VIP Super Bronze

Re: Cisco 6500 PPPoE

Hi Dan,

I do not know what ver of IOS you are running, but have a look at this link for VPND config support from 12.2(33)SXI command reference

http://www.cisco.com/en/US/docs/ios/security/command/reference/sec_t2.html#wp1073816

HTH

Reza

New Member

Re: Cisco 6500 PPPoE

Running 12.2(18)SXF16

vpdn command is not there. Should I be running a different version?

Bronze

Re: Cisco 6500 PPPoE

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Could you provide us the output of show version?

New Member

Re: Cisco 6500 PPPoE

Cisco Internetwork Operating System Software
IOS (tm) s222_rp Software (s222_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF16, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by cisco Systems, Inc.
Compiled Tue 03-Mar-09 14:13 by kellythw
Image text-base: 0x40101040, data-base: 0x42C7EAA0

ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
BOOTLDR: s222_rp Software (s222_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF16, RELEASE SOFTWARE (fc2)

WT01 uptime is 5 days, 21 hours, 26 minutes
Time since WT01 switched to active is 5 days, 21 hours, 25 minutes
System returned to ROM by  power cycle (SP by power-on)
System image file is "disk0:s222-adventerprisek9_wan-mz.122-18.SXF16.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
export@cisco.com. WS-C6506 (R7000) processor (revision 3.0) with 458752K/65536K bytes of memory.
Processor board ID SAL0847642W
R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
SuperLAT software (copyright 1990 by Meridian Technology Corp).
X.25 software, Version 3.0.0.
Bridging software.
TN3270 Emulation software.
1 FlexWAN controller (1 ATM)(1 Channelized T3).
2 Virtual Ethernet/IEEE 802.3 interfaces
10 Gigabit Ethernet/IEEE 802.3 interfaces
4 Serial network interfaces
1 ATM network interface
1 Channelized T3 port
381K bytes of non-volatile configuration memory.

If

cisco

32768K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102

Bronze

Re: Cisco 6500 PPPoE


Only these vpdn/ppoe commands are available for 12.2SX


clear vpdn tunnel pppoe (12.2SX)
debug vpdn pppoe-data (12.2SX)
debug vpdn pppoe-error (12.2SX)
debug vpdn pppoe-events (12.2SX)
debug vpdn pppoe-packet (12.2SX)
vpdn aaa attribute (12.2SX)

debug pppoe (12.2SX)
debug pppoe redundancy (12.2SX)

VIP Super Bronze

Re: Cisco 6500 PPPoE

Dan,

Using the feature navigator, this feature is not supported on the 6500 series.

I am running 12.2.(33)SXI and I tried it and the command is not there.

HTH

Reza

Bronze

Re: Cisco 6500 PPPoE

Here is an old link about this:

This feature is supported on the following platforms:

Cisco 3600 series

Cisco 4500 series

Cisco 4700 series

Cisco 6400 series

Cisco 7500 series

Cisco MC3810 series

Cisco UBR 7200 series

http://www.cisco.com/en/US/docs/ios/12_1t/12_1t2/feature/guide/dtpppofe.html#wp1015343

New Member

Re: Cisco 6500 PPPoE

Is there a way I can handoff pppoe sessions to an external server? L2TP?

I need to terminate 100 ATM PVCs on this router, or an external pppoe server.

Thanks,

New Member

Re: Cisco 6500 PPPoE

I am new to MPLS, could this be benifical to me in this situation?

I also do not have to use pppoe, although I would prefer to.

Hall of Fame Super Silver

Re: Cisco 6500 PPPoE

Hello Dan,

it looks like your C6500 has a supervisor 2 installed from the image name that appears in show ver.

if so MPLS requires specialized linecards like OSM or WAN gigabit interfaces.

AToM (Any Transport over MPLS) could be of help allowing you to send the PPP sessions to some other device but it is not possible at the moment if you haven't at least a sup 720 3BXL.

I would have been surprised to see PPPoE supported on this platform. If you have a C7200 VXR it can be a valid solution.

Hope to help

Giuseppe

New Member

Re: Cisco 6500 PPPoE

Thanks to all !

3248
Views
10
Helpful
11
Replies
CreatePlease to create content