Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Cisco 6500 support LACP & PaGP on the same module?

Hi Sir ...

We had experienced same problem on configing etherchannel. Now we are preparing the configuration about etherchannel on 6500 chassis. But, some paper tell us that Cisco4000 series donot support LACP & PaGP on the module. Is it real?

By the way, Cisco 6509 or IOS could allow engineer config etherchannel LACP & PaGP on this same Giga ethernet module? or TenG Module?

Thanks You!

sean

3 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Super Bronze

Re: Cisco 6500 support LACP & PaGP on the same module?

Hi sean,

Both 6500 and 4500 support Etherchannel using LACP and PAGP. You can also use 10Gig ports or 1Gig ports.

HTH

Reza

Re: Cisco 6500 support LACP & PaGP on the same module?

Hi Sir ...

We had experienced same problem on configing etherchannel. Now we are preparing the configuration about etherchannel on 6500 chassis. But, some paper tell us that Cisco4000 series donot support LACP & PaGP on the module. Is it real?

By the way, Cisco 6509 or IOS could allow engineer config etherchannel LACP & PaGP on this same Giga ethernet module? or TenG Module?

Thanks You!

sean

Hi Sean,

Check out the below link for configuring etherchannel using LACP or PAGP in cisco 6500 and 4000 switches

https://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.1E/native/configuration/guide/channel.html

https://www.cisco.com/en/US/tech/tk389/tk213/technologies_configuration_example09186a0080094470.shtml

Hope to Help !!

Remember to rate the helpful post

Ganesh.H

Hall of Fame Super Silver

Re: Cisco 6500 support LACP & PaGP on the same module?

Hello Sean,

as Ganesh's links should show some old CatOS based LAN switches allowed to configure the bundling protocol per module/linecard only.

>>

set channelprotocol lacp 3 

!--- All ports in module 3 are in LACP channel mode.

This limitation is not present on IOS based C6500 or C4500, so you should be able to have PAGP on bundle1 and LACP on bundle2 with member links that are on ports of the same linecard

Hope to help

Giuseppe

4 REPLIES
VIP Super Bronze

Re: Cisco 6500 support LACP & PaGP on the same module?

Hi sean,

Both 6500 and 4500 support Etherchannel using LACP and PAGP. You can also use 10Gig ports or 1Gig ports.

HTH

Reza

Re: Cisco 6500 support LACP & PaGP on the same module?

Hi Sir ...

We had experienced same problem on configing etherchannel. Now we are preparing the configuration about etherchannel on 6500 chassis. But, some paper tell us that Cisco4000 series donot support LACP & PaGP on the module. Is it real?

By the way, Cisco 6509 or IOS could allow engineer config etherchannel LACP & PaGP on this same Giga ethernet module? or TenG Module?

Thanks You!

sean

Hi Sean,

Check out the below link for configuring etherchannel using LACP or PAGP in cisco 6500 and 4000 switches

https://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.1E/native/configuration/guide/channel.html

https://www.cisco.com/en/US/tech/tk389/tk213/technologies_configuration_example09186a0080094470.shtml

Hope to Help !!

Remember to rate the helpful post

Ganesh.H

Hall of Fame Super Silver

Re: Cisco 6500 support LACP & PaGP on the same module?

Hello Sean,

as Ganesh's links should show some old CatOS based LAN switches allowed to configure the bundling protocol per module/linecard only.

>>

set channelprotocol lacp 3 

!--- All ports in module 3 are in LACP channel mode.

This limitation is not present on IOS based C6500 or C4500, so you should be able to have PAGP on bundle1 and LACP on bundle2 with member links that are on ports of the same linecard

Hope to help

Giuseppe

New Member

Re: Cisco 6500 support LACP & PaGP on the same module?

Yes ....that is where the problem is. Thanks for your response.

1256
Views
0
Helpful
4
Replies
CreatePlease to create content