Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Cisco 6509 with sup2 needs 48 port 1000 BaseT moulde

We have cisco 6509 with the following configuration

System Bootstrap Version: 7.1(1)

System Web Interface Version: Engine Version: 5.3Q ADP Device: Cat6000 ADP Versi

on: 1.7 ADK: 40

Hardware Version: 2.0 Model: WS-C6509 Serial #: SCA054700KA

PS1 Module: WS-CAC-1300W Serial #: SNI05410479

PS2 Module: WS-CAC-1300W Serial #: SNI05421158

Mod Port Model Serial # Versions

--- ---- ------------------- ----------- --------------------------------------

1 2 WS-X6K-SUP2-2GE SAL06334EV0 Hw : 3.10

Fw : 7.1(1)

Fw1: 6.1(3)

Sw : 7.1(2)

Sw1: 7.1(2)

WS-F6K-PFC2 SAL06324E2G Hw : 3.2

2 2 WS-X6K-SUP2-2GE SAL06334EUB Hw : 3.10

Fw : 7.1(1)

Fw1: 6.1(3)

Sw : 7.1(2)

Sw1: 7.1(2)

WS-F6K-PFC2 SAL06324BCH Hw : 3.2

4 48 WS-X6348-RJ-45 SAL0543DJJ4 Hw : 5.0

Fw : 5.4(2)

Sw : 7.1(2)

6 8 WS-X6408A-GBIC SAL06468JTQ Hw : 2.1

Fw : 5.4(2)

Sw : 7.1(2)

7 8 WS-X6408A-GBIC SAL06509Y7N Hw : 2.1

Fw : 5.4(2)

Sw : 7.1(2)

15 1 WS-F6K-MSFC2 SAL06324EAQ Hw : 2.5

Fw : 12.1(11b)E4

Sw : 12.1(11b)E4

16 1 WS-F6K-MSFC2 SAL06334FBN Hw : 2.5

Fw : 12.1(11b)E4

Sw : 12.1(11b)E4

DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 130944K 62484K 68460K 32768K 11264K 21504K 512K 286K 226K

is it possiable to add a 48 port 1000 BaseT module on this? if yes what is the part no: I need to order and also tell us what version should run on these sup

engine

thanks

4 REPLIES

Re: Cisco 6509 with sup2 needs 48 port 1000 BaseT moulde

Hi

I have the below module in 6509

4 4 48 10/100/1000BaseT Ethernet WS-X6548-GE-TX no ok

Thanks

Mahmood

New Member

Re: Cisco 6509 with sup2 needs 48 port 1000 BaseT moulde

are you using the sup engin 2

Thanks

Re: Cisco 6509 with sup2 needs 48 port 1000 BaseT moulde

Hi Friend,

You can go ahead and add a 48 port module in your chassia. It meets all the hardware requirement but nit the software requirement. Cisco's recommended Cat OS version for a 48 port module is 7.6.9.

Please check the release notes for more details on the same :

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/relnotes/ol_1982.htm#wp20834

HTH, Please rate if it does.

-amit singh

New Member

Re: Cisco 6509 with sup2 needs 48 port 1000 BaseT moulde

thanks amit

360
Views
5
Helpful
4
Replies
CreatePlease to create content