Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco 7206VXR unexpected Booting with:Last reset from watchdog reset

Hi

We have issue booting cisco 7206VXR with NPE-G2 on IOS c7200p-advsecurityk9-mz.124-4.XD11.bin. On show version can see that the Router reset (

Last reset from watchdog reset).Below the capture :

Cisco IOS Software, 7200 Software (C7200P-ADVSECURITYK9-M), Version 12.4(4)XD11, RELEASE SOFTWARE (fc4)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Fri 03-Oct-08 15:52 by ccai

ROM: System Bootstrap, Version 12.4(4r)XD5, RELEASE SOFTWARE (fc1)

BOOTLDR: Cisco IOS Software, 7200 Software (C7200P-KBOOT-M), Version 12.4(4)XD2, RELEASE SOFTWARE (fc2)

JKTPZBIIT1-6-WAN02-7206 uptime is 59 minutes

System returned to ROM by error - a Software forced crash, PC 0x1193CEC at 11:06:00 IND Thu Mar 17 2011

System restarted at 14:24:33 IND Fri Jan 24 2014

System image file is "disk2:/c7200p-advsecurityk9-mz.124-4.XD11.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.

Processor board ID 35461839

MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.1

6 slot VXR midplane, Version 2.11

Last reset from watchdog reset

PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.

Current configuration on bus mb1 has a total of 0 bandwidth points.

This configuration is within the PCI bus capacity and is supported.

PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.

Current configuration on bus mb2 has a total of 400 bandwidth points.

This configuration is within the PCI bus capacity and is supported.

Please refer to the following document "Cisco 7200 Series Port Adaptor

Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>

for c7200 bandwidth points oversubscription and usage guidelines.

C7200 PA Jacket Card present in I/O slot (VAM2+ Encryption/Compression engine,)

3 FastEthernet interfaces

3 Gigabit Ethernet interfaces

16 Serial interfaces

1 Virtual Private Network (VPN) Module

2045K bytes of NVRAM.

250880K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).

65536K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

We search on bugtoolkit with ID CSCed93913, CSCea05927. Many issue like this on cisco 7200 but with NPE-G1, are this issue the same like happen for NPE-G2 we have?

And from caveat bug CSCed93913, CSCea05927 doesn't have the solusion yet this time. Have anyone have solution about this issue?

Thanks

183
Views
0
Helpful
0
Replies