Cisco 888 Keeps booting into rommon

[PATRICK DUPONT]

Hi All,

i keep getting into romon for some reason on my C888, the following is an output i really need help doing the Security test in 1 mnth and need to use the CCP and this is the only router, Trued Confreg 2102,2101 still keeps booting into Rommon any else have any ideas?

rommon 22 > reset

System Bootstrap, Version 12.4(15r)XZ2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.

C880 platform with 262144 Kbytes of main memory

Upgrade ROMMON initialized
loadprog: bad file magic number:      0x0
boot: cannot load "flash:"

System Bootstrap, Version 12.4(15r)XZ2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.

C880 platform with 262144 Kbytes of main memory

Upgrade ROMMON initialized
loadprog: bad file magic number:      0x0
boot: cannot load "flash:"

System Bootstrap, Version 12.4(15r)XZ2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.

C880 platform with 262144 Kbytes of main memory

Upgrade ROMMON initialized

==============================================================

rommon 1 >
System Bootstrap, Version 12.4(15r)XZ2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.

C880 platform with 262144 Kbytes of main memory

Upgrade ROMMON initialized
loadprog: bad file magic number:      0x0
boot: cannot load "flash:"

System Bootstrap, Version 12.4(15r)XZ2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.

C880 platform with 262144 Kbytes of main memory

Upgrade ROMMON initialized

Thank you

Pat

[Kostas Kyriakos]

Hello.

It looks like there's no image present in Flash. If there is one, it is probably corrupted. You need to follow the instructions from the link below in order to load new ios provided you have a valid CCO account:

http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/software/configuration/guide/rommon.html

Hope this helps.

[thaleradam]

I also had a problem like this. My IOS was corrupted, so I downloaded another file, and I uploaded it with TFTP.

Just type in the following in rommon mode:

IP_ADDRESS= ip_address

IP_SUBNET_MASK= ip_address

DEFAULT_GATEWAY= ip_address

TFTP_SERVER= ip_address

TFTP_FILE= filename

tftpdnld

it'll take 5-10 minutes. Unfortunately slower than global conf mode.

Regard

Adam.

[riroe]

“Thank you for your question.  This community is for Cisco Small Business products and your question is in reference to a Cisco Elite/Classic product.  Please post your question in the Cisco NetPro forums located here:

http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748.SJ3A?page=Network_Infrastructure_discussion

This forum has subject matter experts on Cisco Elite/Classic products that may be able to answer your question.”

THANKS

[Phillip Remaker]

Do a "dir flash:" and see if you have a valid image installed.  If not, install one with TFTP per the link provided by a previous poster.

[PATRICK DUPONT]

Thank you that has Answered, it has worked.. urghhhh thank yo again for all the help./