Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco Auto-QoS on Cisco 4500

Hi guys,

 

i wanted to activate auto-qos on my LAN, but when i get to the C4500 i find that the command auto .... is not accepted 

 

Sh Version :

Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.05.03.E RELEASE SOFTWARE (fc1)

 

 

is it due to my version ?? i want a confirmation !!

 

 

Thanks;;

9 REPLIES
New Member

http://tools.cisco.com/ITDIT

New Member

so im dead, is there any

so im dead, is there any solution so it can support the auto-qos??

 

thanks please

Cisco Employee

Oussama,If you can provide a

Oussama,

If you can provide a complete "show version", that will help more.

Starting with Cisco Release XE 3.3.0(SG) and 15.1(1)SG, the Catalyst 4500 Series Switch supports the "auto qos srnd4" command.

Kind regards,

Ed

New Member

Hi Educurz, okay here is the

Hi Educurz,

 

okay here is the sh version all of it :)

 

 

i don"t know why is not working!!!!

Cisco Employee

Thank you Oussama,Due to Auto

Thank you Oussama,

Due to Auto Qos having 'set' commands ip routing will need to be enabled globally on the
switch. Have you enabled IP routing globally?

Kind regards,

Ed.

New Member

yes it is enabled, so what

yes it is enabled, so what the problem then check this :

 

CEG01-SWF-1(config)#interface g2/1
CEG01-SWF-1(config-if)#au
CEG01-SWF-1(config-if)#aut
CEG01-SWF-1(config-if)#auto
CEG01-SWF-1(config-if)#auto?
% Unrecognized command
CEG01-SWF-1(config-if)#auto

New Member

switch(config)#int g1/1switch

switch(config)#int g1/1
switch(config-if)#auto ?
  qos  Configure AutoQoS

 

switch(config-if)#auto qos ?
  classify  Configure classification for untrusted devices
  trust     Trust the DSCP/CoS marking
  video     Configure AutoQoS for video devices
  voip      Configure AutoQoS for VoIP

 

Its there. I am on a 4510 with WS-X45-SUP8-E running Catalyst 4500 L3 Switch Software (cat4500es8-UNIVERSAL-M), Version 03.03.01.XO RELEASE SOFTWARE 

 

New Member

hi ubhen,  here you go  CEG01

hi ubhen,

 

 

here you go 

 

CEG01-SWF-1(config)#interface g2/1
CEG01-SWF-1(config-if)#au
CEG01-SWF-1(config-if)#aut
CEG01-SWF-1(config-if)#auto
CEG01-SWF-1(config-if)#auto?
% Unrecognized command
CEG01-SWF-1(config-if)#auto

 

i did it on my switch , i dont understand

 

New Member

i have a c4506-E with a

i have a c4506-E with a supervisor : WS-X45-SUP7L-E 

 

:)

381
Views
0
Helpful
9
Replies