Hello All,
I am configuring VSS between two 4500x switches, and am having difficulty. I followed the below insturctions from cisco's site, however I both times I've tried this, the standby switch continues to reboot right when it finishes booting. The below link was what I used to setup the VSS, the config begins below "Converting to a VSS".
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/15.1.2/XE_340/configuration/guide/vss.html#wp1062785
Below are the logs I get from the standby switch right before it reboots. The primary switch says it connects to it's peer, then about a second later it disconnects.
*Dec 3 14:33:45.276: %GBIC_SECURITY-4-UNSUPPORTED_GBIC_INSERTED: Unsupported transceiver inserted in port 460
*Dec 3 14:33:45.276: %C4K_CHASSIS-3-TRANSCEIVERCRCINTEGRITYCHECKFAILED: Transceiver integrity check on port 460 failed: bad crc
*Dec 3 14:33:47.330: %GBIC_SECURITY-4-UNSUPPORTED_GBIC_INSERTED: Unsupported transceiver inserted in port 461
*Dec 3 14:33:47.330: %C4K_CHASSIS-3-TRANSCEIVERCRCINTEGRITYCHECKFAILED: Transceiver integrity check on port 461 failed: bad crc
*Dec 3 14:33:49.534: %C4K_IOSINTF-5-LMPHWSESSIONSTATE: Lmp HW session UP on slot 11 port 1.
*Dec 3 14:33:51.646: %C4K_IOSINTF-5-LMPHWSESSIONSTATE: Lmp HW session UP on slot 11 port 2.
*Dec 3 14:34:05.531: %VSLP-5-VSL_UP: Ready for control traffic
*Dec 3 14:34:09.539: %VSLP-5-RRP_ROLE_RESOLVED: Role resolved as STANDBY by VSLP
*Dec 3 14:34:47.100: %C4K_REDUNDANCY-3-COMMUNICATION: STANDBY:Communication with the peer Supervisor has been established
*Dec 3 14:35:05.453: %SPANTREE-5-EXTENDED_SYSID: STANDBY:Extended SysId enabled for type vlan
*Dec 3 14:35:06.240: %VSLP-3-VSLP_LMP_FAIL_REASON: STANDBY:Te2/1/1: Link down
*Dec 3 14:35:06.253: %VSLP-3-VSLP_LMP_FAIL_REASON: STANDBY:Te2/1/2: Link down
*Dec 3 14:35:06.253: %VSLP-2-VSL_DOWN: STANDBY: All VSL links went down while switch is in Standby role
*Dec 3 14:35:06.254: %C4K_REDUNDANCY-3-NOT_READY_FOR_SWITCHOVER: STANDBY:The active Supervisor failed but standby supervisor cannot initiate Switchover activity. Resetting standby Supervisor.
*Dec 3 14:35:06.386: %RF-5-RF_RELOAD: STANDBY:Self Reload. Reason: Standby not ready for switchover
*Dec 3 14:35:06.414: %SYS-2-NOBLOCK: STANDBY:sleep for with blocking disabled. -Process= "Cat4k Mgmt LoPri", ipl= 0, pid= 86
-Traceback= 1#251bc17810f5fe5cfe9c51cc9cacd46b :12252000+2699F4C :12252000+269A310 :12252000+1F1B55C :12252000+38D4044 :12252000+F90A18 :12252000+3F7AB28 :12252000+3F8A7C4 :12252000+F90C78 :12252000+1F1ED44 :12252000+FB3100 :12252000+6088234 :12252000+1BD80D8 :12252000+6088088 :12252000+FA3294 :12252000+FDA144 :12252000+FDA220
*Dec 3 14:35:06.418: %SPILIB-3-PL_NO_SUSPEND_ERRMSG: STANDBY:SPI process suspend not allowed
-Traceback= 1#251bc17810f5fe5cfe9c51cc9cacd46b :12252000+2699F4C :12252000+269A310 spilib:4D53B000+30380 spilib:4D53B000+11BF0 spilib:4D53B000+12038 shutdown:4CB54000+13F40 shutdown:4CB54000+9CCC :12252000+1BFB1CC :12252000+1BEB540 :12252000+1F1ED44 :12252000+FB3100 :12252000+6088234 :12252000+1BD80D8 :12252000+6088088 :12252000+FA3294 :12252000+FDA144
*Dec 3 14:35:06.493: %SYS-5-RELOAD: STANDBY:Reload requested by Platform redundancy manager. Reload Reason: Standby not ready for switchover.Please stand by while rebooting the system...
Restarting system.
Any help or advice would be greatly appreciated.
