cold start

prashantrecon · ‎01-04-2012

Hi Team,

we haven't rebooted the switch but still logs show it has udergone a coldstart is there any hardware eeror

000007: *Jan 4 02:16:13: %SNMP-5-COLDSTART: SNMP agent on host nihilent01 is undergoing a cold start

00:00:34: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor for this switch

00:00:35: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

Firmware compiled 16-Aug-07 11:57 by integ Build [100]

00:00:36: %OIR-6-CONSOLE: Changing console ownership to route processor

00:00:36: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

00:01:43: SP: SP: Currently running ROMMON from S (Gold) region

00:01:52: %SPANTREE-SP-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology

00:01:57: %OIR-SP-6-INSPS: Power supply inserted in slot 1

00:01:57: %C6KPWR-SP-4-PSOK: power supply 1 turned on.

00:01:58: %OIR-SP-6-INSPS: Power supply inserted in slot 2

00:01:58: %C6KPWR-SP-4-PSOK: power supply 2 turned on.

00:01:58: %C6KPWR-SP-4-PSREDUNDANTBOTHSUPPLY: in power-redundancy mode, system is operating on both power supplies.

00:01:58: %SYS-SP-5-RESTART: System restarted --

Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH, RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Compiled Sun 19-Aug-07 07:52 by prod_rel_team

00:01:59: %SYS-SP-6-BOOTTIME: Time taken to reboot after reload = 156 seconds

*Jan 4 02:16:26: %FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 6.

*Jan 4 02:16:26: %FABRIC-SP-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Module in slot 6 became active.

*Jan 4 02:16:28: %DIAG-SP-6-RUN_MINIMUM: Module 6: Running Minimal Diagnostics...

000008: *Jan 4 02:16:50: %SNMP-5-MODULETRAP: Module 6 [Up] Trap

*Jan 4 02:16:49: %DIAG-SP-6-DIAG_OK: Module 6: Passed Online Diagnostics

*Jan 4 02:16:50: %OIR-SP-6-INSCARD: Card inserted in slot 6, interfaces are now online

00:00:02: DaughterBoard (Centralized Forwarding Card)

rsimoni · ‎01-04-2012

no error message in bootup logs; first impression is that you got a power cut.

please paste the following:

show module

show version

remo com sw show version

remo com sw show nvlog

show diagnostic events

if you have redundant supervisor take also:

rem command standby-sp show nvlog

show redundancy

show redundancy switchover

regards,

Riccardo

prashantrecon · ‎01-04-2012

i

Please find the details below

nihilent01#show redundancy

Redundant System Information :

------------------------------

Available system uptime = 8 hours, 35 minutes

Switchovers system experienced = 0

Standby failures = 0

Last switchover reason = none

Hardware Mode = Simplex

Configured Redundancy Mode = sso

Operating Redundancy Mode = sso

Maintenance Mode = Disabled

Communications = Down Reason: Simplex mode

Current Processor Information :

-------------------------------

Active Location = slot 6

Current Software state = ACTIVE

Uptime in current state = 8 hours, 34 minutes

Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH, RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Compiled Sun 19-Aug-07 07:38 by prod_rel_team

BOOT = sup-bootdisk:,1;

CONFIG_FILE =

BOOTLDR =

Configuration register = 0x2102

Peer (slot: unavailable) information is not available because it is in 'DISABLED' state

nihilent01#show redundancy switchover

Switchovers this system has experienced : 0

Last switchover reason : None.

Uptime since this supervisor switched to active : 8 hours, 36 minutes

Total system uptime from reload : 8 hours, 36 minutes

nihilent01#show redundancy switchover

Switchovers this system has experienced : 0

Last switchover reason : None.

Uptime since this supervisor switched to active : 8 hours, 36 minutes

Total system uptime from reload : 8 hours, 36 minutes

nihilent01#show module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1202CRVV

2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1202CN7J

5 2 Supervisor Engine 720 (Other) WS-SUP720-3B SAL114990M2

6 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL114990M2

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 001e.bef8.6cd0 to 001e.bef8.6cff 2.7 12.2(14r)S5 12.2(33)SXH Ok

2 001e.f77f.b500 to 001e.f77f.b52f 2.7 12.2(14r)S5 12.2(33)SXH Ok

5 0016.9de6.6200 to 0016.9de6.6203 5.6 Unknown Unknown Other

6 0016.9de6.6200 to 0016.9de6.6203 5.6 8.5(2) 12.2(33)SXH Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

1 Centralized Forwarding Card WS-F6700-CFC SAL1202CRJT 4.0 Ok

2 Centralized Forwarding Card WS-F6700-CFC SAL1202CRK6 4.0 Ok

6 Policy Feature Card 3 WS-F6K-PFC3B SAL1149978X 2.3 Ok

6 MSFC3 Daughterboard WS-SUP720 SAL114992AD 3.1 Ok

Mod Online Diag Status

---- -------------------

1 Pass

2 Pass

5 Not Applicable

6 Pass

rsimoni · ‎01-04-2012

where is the rest of the outputs I requested?

I have some ideas of what heppened but I need all the outputs I requested (some of them will not give any info as the sup on slot 5 is not Other - probably in ROMMON - but I could get some valid info from the other outputs I asked you).

You'd better paste all the outputs in a txt file and attach it to this thread.

Leo Laohoo · ‎01-04-2012

Slot 5 and 6 are currently occupied by a pair of Sup720. Active card is Slot 6. Maybe Slot 5 Sup720 is running a different IOS? Have you tried to remove and re-insert the card and see what happens?

prashantrecon · ‎01-05-2012

HI Leo,

Are u taking about slot 5 to remove and re-insert .

rsimoni · ‎01-05-2012

Hi Prashant,

do you want to solve the 'other' status of your sup or do you want to know why the switch reloaded?

Riccardo

Leo Laohoo · ‎01-05-2012

Are u taking about slot 5 to remove and re-insert .

Yes.