01-13-2007 06:01 AM - edited 03-05-2019 01:45 PM
I am trying copy startup-config running-config
The above command is failing with an error.
User Access Verification
Password:
MLS-77-1>enable
Password:
MLS-77-1#copy startup-config running-config
% Copy to running-config failed because configuration changes are locked
And if I try the command after few seconds, it will be successful.
What can be the problem?
01-13-2007 06:57 AM
What model is this device and is it native or hybrid os ?? If its 6500 running hybrid then there is no write memory or copy run start commands , confgiurations are saved as soon as you enter the information . Just by looking at your prompt it looks like hybrid so there is no need to save any config it is saved automatically , but of course it is always smart to save a copy on a tftp server somewhere in case the hardware fails .
01-13-2007 07:27 AM
I am using 6509 with Image..
c6sup22-psv-mz.121-26.E5.bin
01-13-2007 08:08 AM
Hi
I think its the issue with u r access level privilages on the device.Can u confrim what level of access u have on this device.
Thanks
Mahmood
01-13-2007 10:26 AM
Do a show mod command and post here and we can tell better . To me it looks your first post prompt is catos but I could be wrong.
01-14-2007 12:03 AM
MLS-77-1#sh mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 SAL0749QEGC
2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-S2U-MSFC2 SAL0749QEFW
3 48 48-port 10/100 mb RJ45 WS-X6148-RJ-45 SAL0749Q6YP
4 16 SFM-capable 16 port 10/100/1000mb RJ45 WS-X6516-GE-TX SAL0748Q5DP
6 0 2 port adapter FlexWAN WS-X6182-2PA SAD0710005F
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0006.d65d.afd8 to 0006.d65d.afd9 5.0 7.1(1) 12.1(26)E5 Ok
2 0009.1246.d664 to 0009.1246.d665 5.0 7.1(1) 12.1(26)E5 Ok
3 000e.3893.7780 to 000e.3893.77af 1.3 5.4(2) 8.5(0.9)TFW3 Ok
4 000e.38c3.dac0 to 000e.38c3.dacf 2.5 6.3(1) 8.5(0.9)TFW3 Ok
6 0008.7cd6.5180 to 0008.7cd6.51bf 1.5 12.1(26)E5 12.1(26)E5 Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------- --------------- --------------- ------- -------
1 Policy Feature Card 2 WS-F6K-PFC2 SAL0749QD34 3.4 Ok
1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL0749QBQ2 2.6 Ok
2 Policy Feature Card 2 WS-F6K-PFC2 SAL0747PZWP 3.4 Ok
2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL0749QBNY 2.6 Ok
Mod Online Diag Status
--- -------------------
1 Pass
2 Pass
3 Pass
4 Pass
6 Not Applicable
01-14-2007 03:16 AM
I think the reason for that error is because I am trying to run the command when both the active and standby card are trying to sync.
Jan 14 16:10:13.818 GMT: %PFREDUN-SP-6-ACTIVE: Standby initializing for R
PR-PLUS modesh
Jan 14 16:10:14.070 GMT: %PFINIT-SP-5-CONFIG_SYNC: Sync'ing the startup c
onfiguration to the standby Router mod
### here I run the command.. ##########
MLS-77-1#copy startup-config running-config
% Copy to running-config failed because configuration changes are locked
####### here the sync is completed #######
Jan 14 16:11:14.607 GMT: %SNMP-5-MODULETRAP: Module 1 [Up] Trap
Jan 14 16:11:14.091 GMT: %DIAG-SP-6-RUN_MINIMUM: Module 1: Running Minimu
m Online Diagnostics...
Jan 14 16:11:14.091 GMT: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diag
nostics
Jan 14 16:11:14.503 GMT: %OIR-SP-6-INSCARD: Card inserted in slot 1, inte
rfaces are now onlinesh mod
00:00:08: %OIR-SP-STDBY-6-CONSOLE: Changing console ownership to route pr
ocessor
00:00:42: %PFREDUN-SP-STDBY-6-STANDBY: Initializing for RPR-PLUS mode
00:00:47: %SPANTREE-SP-STDBY-5-EXTENDED_SYSID: Extended SysId enabled for
type vlan
00:00:47: SP-STDBY: SP: Currently running ROMMON from S (Gold) region
00:00:58: %DIAG-SP-STDBY-6-RUN_MINIMUM: Module 1: Running Minimum Online
Diagnostics...
00:01:36: %DIAG-SP-STDBY-6-DIAG_OK: Module 1: Passed Online Diagnostics
00:01:50: %SW_VLAN-SP-STDBY-6-VT
If I try to save configs before or after this sync process then I will be able to save the configs properly.
Actually I am writing a upgrade script, and it was failing as it was unable to save the configs.
Thanks anyways to all of you.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide