Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Copy Run Start Problem

when running "copy running-configuration startup-configuration, I get the following error.

%Error opening flash:running-configuration (File not found)

6 REPLIES
Hall of Fame Super Bronze

Re: Copy Run Start Problem

Please post your 'show version' from this device .

Can you also try the command 'wr mem' and see if it works ?

Community Member

Re: Copy Run Start Problem

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(4)XC4, RELEASE SOFTWARE (fc1)

Synched to technology version 12.4(5.13)T

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 24-Jul-06 18:33 by ealyon

ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)

ROM: Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(4)XC4, RELEASE SOFTWARE (fc1)

DPI-CME-2811 uptime is 16 weeks, 1 day, 23 hours, 31 minutes

System returned to ROM by Reload Command

System restarted at 08:53:53 EDT Wed Mar 14 2007

System image file is "flash:c2800nm-advipservicesk9-mz.124-4.XC4.bin"

Hall of Fame Super Bronze

Re: Copy Run Start Problem

That's not a complete 'show version'. I was looking for the current config-register setting.

Please repost the entire show version.

Did you try 'wr mem' as suggested ?

Can you also post the output from typing

'show priv'.

Re: Copy Run Start Problem

HI,

Its better to capture & attach the complete output of "show tech-support" for full - analysis.

Best Regards,

Guru Prasad R

Community Member

Re: Copy Run Start Problem

WR MEM

DPI-CME-2811#wr mem

Building configuration...

Compressed configuration from 29043 bytes to 13778 bytes[OK]

Show Version

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(4)XC4, RELEASE SOFTWARE (fc1)

Synched to technology version 12.4(5.13)T

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Mon 24-Jul-06 18:33 by ealyon

ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)

ROM: Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(4)XC4, RELEASE SOFTWARE (fc1)

DPI-CME-2811 uptime is 16 weeks, 1 day, 23 hours, 52 minutes

System returned to ROM by Reload Command

System restarted at 08:53:53 EDT Wed Mar 14 2007

System image file is "flash:c2800nm-advipservicesk9-mz.124-4.XC4.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 2811 (revision 53.51) with 247808K/14336K bytes of memory.

Processor board ID FTX0908A12N

2 FastEthernet interfaces

25 Serial interfaces

1 terminal line

2 Channelized T1/PRI ports

2 Virtual Private Network (VPN) Modules

2 Voice FXO interfaces

1 cisco service engine(s)

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62592K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

DPI-CME-2811#

SHOW PRIV

Current privilege level is 15

Hall of Fame Super Bronze

Re: Copy Run Start Problem

Gosh, I can't believe I overlooked the obvious.

The command is

copy running-config startup-config

not

copy running-configuration startup-configuration

running-configuration will be treated as a file name.

1396
Views
3
Helpful
6
Replies
CreatePlease to create content