cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2712
Views
0
Helpful
2
Replies

crc errors on uplink ports to our Nexus 7000

broow
Level 1
Level 1


we have several uplink ports on a verity of cisco switches connecting to the nexus 7000, recording CRC errors.

most are trunked ports with the following configuration.

access switch:

interface GigabitEthernet0/25

switchport trunk encapsulation dot1q

switchport mode trunk

switchport nonegotiate

end

nexus port:

interface Ethernet1/19

switchport

switchport mode trunk

no shutdown.

nexus is running:

version 5.2(1)

switch is running:

ws-c3560G-24TS    12.2(35)SE5

do not see any performance issues, just crc errors.  Any ideas?

2 Replies 2

Dale Miller
Cisco Employee
Cisco Employee

What type of module is in the N7K? Can you tell us if the problem is on 1 module or across multiple? Do the errors also show up as input errors?

Thanks,
Dale

modules:

48 port 1000 Mbps Optical Ethernet Module  N&K-M148GS-11

it is happening over two modules we have.

Nexus 7K Mod  Ports  Module-Type                        Model              Status ---  -----  ----------------------------------- ------------------ ----------

1    48    1000 Mbps Optical Ethernet Module  N7K-M148GS-11      ok

2    8      10 Gbps Ethernet XL Module          N7K-M108X2-12L    ok

3    48    10/100/1000 Mbps Ethernet Module    N7K-M148GT-11      ok

5    0      Supervisor module-1X                N7K-SUP1          active *

6    0      Supervisor module-1X                N7K-SUP1          ha-standby

8    48    10/100/1000 Mbps Ethernet Module    N7K-M148GT-11      ok

9    8      10 Gbps Ethernet XL Module          N7K-M108X2-12L    ok

10  48    1000 Mbps Optical Ethernet Module  N7K-M148GS-11      ok

example of access switch uplink port:

GigabitEthernet0/25 is up, line protocol is up (connected)

Hardware is Gigabit Ethernet, address is 3cdf.1ec7.f999 (bia 3cdf.1ec7.f999)   MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,     reliability 255/255, txload 1/255, rxload 20/255   Encapsulation ARPA, loopback not set   Keepalive not set   Full-duplex, 1000Mb/s, link type is auto, media type is 1000BaseSX SFP   input flow-control is off, output flow-control is unsupported   ARP type: ARPA, ARP Timeout 04:00:00  

Last input 00:00:00, output 00:00:00, output hang never  

Last clearing of "show interface" counters 2d19h   Input queue: 0/75/0/0 (size/max/drops/flushes);

Total output drops: 0   Queueing strategy: fifo   Output queue: 0/40 (size/max)

5 minute input rate 79949000 bits/sec, 7092 packets/sec  

5 minute output rate 1975000 bits/sec, 3432 packets/sec    

1638438298 packets input, 2268962487134 bytes, 0 no buffer    

Received 98383573 broadcasts (0 multicasts)     0 runts, 0 giants, 0 throttles    

96602 input errors, 96602 CRC, 0 frame, 0 overrun, 0 ignored    

0 watchdog, 62304948 multicast, 0 pause input     0 input packets with dribble condition detected    

742062096 packets output, 96087437772 bytes, 0 underruns    

0 output errors, 0 collisions, 0 interface resets    

0 babbles, 0 late collision, 0 deferred    

0 lost carrier, 0 no carrier, 0 PAUSE output    

0 output buffer failures, 0 output buffers swapped out

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card