Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Create VLAN on Cisco 2948G switch running on CAT OS

Hello Experts,

I'm trying to configure VLAN on Cisco 2948G switch running on CAT OS and getting the following error:

VTP advertisements transmitting temporarily stopped,

and will resume after the command finishes.

Cannot add/modify VLANs on a VTP server without a domain name.

I'm using this command "set vlan 2 name corporate" that I believe is correct.

Please assist.

Thanks.

9 REPLIES
VIP Purple

Re: Create VLAN on Cisco 2948G switch running on CAT OS

I configured my last CatOS switch probably 10 years ago, so I don't really remember if the followind should be ok. But the message sounds like that you should configure VTP correctly:

set vtp domain YOUR-VTP-DOMAIN mode server

   or

set vtp domain YOUR-VTP-DOMAIN mode transparent


--

Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni
New Member

Re: Create VLAN on Cisco 2948G switch running on CAT OS

I don't want to configure VTP, just create a simple VLAN, that's it..

Sent from Cisco Technical Support iPhone App

VIP Purple

Re: Create VLAN on Cisco 2948G switch running on CAT OS

if you don't want VTP, then configure it just with the correct mode for that which is transparent.


Sent from Cisco Technical Support iPad App


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni
New Member

Re: Create VLAN on Cisco 2948G switch running on CAT OS

What is a correct mode as I'm not good on CAT OS. Please provide correct command, if possible

Thanks

Sent from Cisco Technical Support iPhone App

VIP Purple

Re: Create VLAN on Cisco 2948G switch running on CAT OS

that should be:

set vtp domain YOUR-VTP-DOMAIN mode transparent


Sent from Cisco Technical Support iPad App


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni
New Member

Re: Create VLAN on Cisco 2948G switch running on CAT OS

Is it compulsory?

Sent from Cisco Technical Support iPhone App

VIP Purple

Re: Create VLAN on Cisco 2948G switch running on CAT OS

I don't have any more documentation on that device/CatOS. But your error-code sounds like if it would be needed to correct your config.


Sent from Cisco Technical Support iPad App


--
Don't stop after you've improved your network! Improve the world by lending money to the working poor: http://www.kiva.org/invitedby/karsteni
Cisco Employee

Create VLAN on Cisco 2948G switch running on CAT OS

Ray,

CATOS commands:

Complete these steps:

  1. Issue this command in order to set the domain name:

    set vtp domain name
    
    

    Note: When you configure a new switch, the VTP domain name should be configured before you create any non-default VLANs.

  2. Issue this command in order to set the mode:

    set vtp mode [server | client | transparent]
    
  3. Issue these commands in order to monitor the VTP operation and status:

    show vtp domain
    show vtp statistics

HTH

Regards

Inayath

*Plz rate all usefull posts.

Purple

Re: Create VLAN on Cisco 2948G switch running on CAT OS

334
Views
3
Helpful
9
Replies