11-17-2013 08:04 AM - edited 03-07-2019 04:38 PM
whenever i connect the access point in the network i could not connect the access point using the GUI interface,but when i connect the access point using the cable from my pc direct to access point i can easily connect using GUI ,
So please can some one help me in this regard i have this issue ,i am not getting solution,.
for the reference i am also copying the run config from my access point.
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
logging rate-limit console 9
enable secret 5 $1$2ggM$rSKvqdqz2qCnaAMK1rGcB.
enable password 7 094F471A1A0A
!
no aaa new-model
!
!
dot11 syslog
!
dot11 ssid tadrees-ap2
vlan 2
authentication open
guest-mode
!
dot11 network-map
!
!
username Cisco password 7 072C285F4D06
username admin password 7 14141B180F0B
!
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption vlan 2 key 1 size 40bit 7 E087398FE03F transmit-key
encryption vlan 2 mode wep mandatory
!
ssid tadrees-ap2
!
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
!
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
!
encryption vlan 2 key 1 size 40bit 7 A782F312341F transmit-key
encryption vlan 2 mode wep mandatory
!
ssid tadrees-ap2
!
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio1.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
!
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface GigabitEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
!
interface BVI1
ip address 10.10.2.12 255.255.255.0
no ip route-cache
!
ip default-gateway 10.10.2.200
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
!
end
11-17-2013 08:31 AM
HI Mohammed,
Please follow this config and check it.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008055c39a.shtml
Regards
Hope it helps.
11-17-2013 08:57 AM
hi sandeep if you read what i mention above in my discussion ,i configure everything,when i connect pc directly to access point i can access gui,but when i connect access point in the network and try to connect using gui from pc i cannot,
and i can even ping the access point but i cant access the access point using gui .
11-17-2013 09:31 AM
What version of IOS u have on AP??
Regards
11-17-2013 09:59 AM
version 12.4
11-17-2013 04:50 PM
Hi,
What is the configuration of the switch port the access point is connected to? Is it an access port or trunk port?
Thanks
John
11-18-2013 07:28 AM
dear john,
please if you dont mind can you explain me what if configured trunk port,or access port ,that will playe role in access the gui interface for the access point .
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: