Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

Dows Cisco Routers 2921 supports WIC Cards?

I have trouble to install a Frame Relay service because the vendor sold me WIC cards but i think 2921 only supports HWIC cards

Here's the output of the show diag:

Router Llano Mall
ag321-acc-rou-01#sh diag | b WIC Slot 1:
         WIC Slot 1:
         Serial 2T (12in1)
         WIC module not supported/disabled in this slot
         Hardware revision 1.0           Board revision B0
         Serial number     32098957      Part number    800-03181-02
         FRU Part Number     WIC-2T=          
         Test history      0x0           RMA number     00-00-00
         Connector type    PCI
         EEPROM format version 1
         EEPROM contents (hex):
           0x20: 01 12 01 00 01 E9 CA 8D 50 0C 6D 02 00 00 00 00
           0x30: 58 00 00 00 04 04 08 00 FF FF FF FF FF FF FF FF

Router Cumaná
ag521-acc-rou-01#sh diag | b WIC Slot 0:     
         WIC Slot 0:
         HWIC Serial 2T WAN daughter card
         Hardware Revision        : 2.0
         Top Assy. Part Number    : 800-34379-01
         Board Revision           : A0
         Deviation Number         : 115024
         Fab Version              : 02
         PCB Serial Number        : FOC15023T8C
         RMA Test History         : 00
         RMA Number               : 0-0-0-0
         RMA History              : 00
         Fab Part Number          : 28-8141-01
         Product (FRU) Number     : HWIC-2T
         Version Identifier       : V03
         CLEI Code                : COUIA1RCAB
         EEPROM format version 4
         EEPROM contents (hex):
           0x00: 04 FF 40 05 89 41 02 00 C0 46 03 20 00 86 4B 01
           0x10: 42 41 30 88 00 01 C1 50 02 02 C1 8B 46 4F 43 31
           0x20: 35 30 32 33 54 38 43 03 00 81 00 00 00 00 04 00

           0x30: 85 1C 1F CD 01 CB 87 48 57 49 43 2D 32 54 89 56
           0x40: 30 33 20 D9 02 40 C1 C6 8A 43 4F 55 49 41 31 52
           0x50: 43 41 42 FF FF FF FF FF FF FF FF FF FF FF FF FF
           0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
           0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Is there any command or any form that i can use this card to implement frame relay?

Thanks in advance

Alejandro

Everyone's tags (5)
1 ACCEPTED SOLUTION

Accepted Solutions

Re: Dows Cisco Routers 2921 supports WIC Cards?

It looks like it's unsupported and a 2921 ISR G2 would accept an HWIC-2T instead.

http://www.cisco.com/en/US/products/ps10537/products_relevant_interfaces_and_modules.html#serialwan

Sent from Cisco Technical Support iPhone App

1 REPLY

Re: Dows Cisco Routers 2921 supports WIC Cards?

It looks like it's unsupported and a 2921 ISR G2 would accept an HWIC-2T instead.

http://www.cisco.com/en/US/products/ps10537/products_relevant_interfaces_and_modules.html#serialwan

Sent from Cisco Technical Support iPhone App

859
Views
0
Helpful
1
Replies