Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

E1 line configuration on iOS

Hi All,

I have a cisco router c2600 version 12.4T. I'm trying to configure the E1 on that router and connectto an eFax server. but it seems that there is some thing wrong in the configuration. Are there anything wrong in the config ??

Current configuration : 2759 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname MAA-FAX

!

boot-start-marker

boot system flash

boot system flash c2600-ipvoice-mz.124-15.T14.bin

boot-end-marker

!

card type e1 1 1

enable secret 5 $1$Eu5N$LNIs2iojGJB.VUSeYS45T1

!

no aaa new-model

no network-clock-participate slot 1

no network-clock-participate wic 0

ip cef

!

!

!

!

ip domain name main.knpcdom.net

multilink bundle-name authenticated

isdn switch-type primary-net5

voice-card 1

!

!

!

!

voice service voip

allow-connections h323 to h323

fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none

h323

!

!

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g729br8

!

!

!

!

!

!

!

!

!

!

!

!

!

!

archive

log config

  hidekeys

!

!

controller E1 1/0

pri-group timeslots 1-31

!

controller E1 1/1

pri-group timeslots 1-31

!

!

!

!

!

interface FastEthernet0/0

ip address x.x.x.x(voice GW ip) 255.255.255.0

duplex auto

speed auto

h323-gateway voip interface

!

interface Serial1/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

no cdp enable

!

interface Serial1/1:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

no cdp enable

!

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 x.x.x.x(Voice GW ip -last digit is 1)

!

no ip http server

!

no logging trap

!

!

control-plane

!

!

!

voice-port 1/0:15

!

voice-port 1/1:15

!

!

!

!

!

dial-peer voice 100 voip

preference 2

destination-pattern [1234567890]...

voice-class codec 1

session target ipv4:x.x.x.x (the eFax server ip)

dtmf-relay h245-alphanumeric

fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none

no vad

!

dial-peer voice 200 pots

destination-pattern 2.......

port 1/0:15

!

dial-peer voice 101 voip

preference 1

destination-pattern [1234567890]...

voice-class codec 1

session target ipv4:x.x.x.x (the eFax backup server ip)

dtmf-relay h245-alphanumeric

fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none

no vad

!

dial-peer voice 10 voip

translation-profile incoming rightfax

voice-class codec 1

incoming called-number 2.......

dtmf-relay h245-alphanumeric

no vad

!

dial-peer voice 2 pots

incoming called-number .

direct-inward-dial

!

dial-peer voice 102 voip

destination-pattern 8...

session target ipv4:x.x.x.x (CUCM ip)

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 103 voip

preference 1

destination-pattern 8...

session target ipv4:x.x.x.x (CUCM backup ip)

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 1 voip

voice-class codec 1

incoming called-number .

dtmf-relay h245-alphanumeric

no vad

!

!

!

line con 0

password ******

login

line aux 0

line vty 0 4

password ******

login

transport input all

!

!

end

Thank alot

Everyone's tags (2)
2 REPLIES
Hall of Fame Super Gold

E1 line configuration on iOS

I am surprised to see encapsulation hdlc on the serial interfaces. Are you sure that the server is processing hdlc?

HTH

Rick

Silver

E1 line configuration on iOS

Can you post output of "debug isdn q921" and "debug isdn q931" during attempt to make a call?

HTH,
Dragan

HTH, Dragan
271
Views
0
Helpful
2
Replies
CreatePlease to create content