cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
427
Views
0
Helpful
3
Replies

EIGRP routing

fgasimzade
Level 4
Level 4

The issue is to configure routers with EIGRP to send only desired routes. I heard this is somehow done through prefix lists and route map, but I dont know exactly. Has anyone dealt with it? Or can anyone suggest any links with configuration guide?

1 Accepted Solution

Accepted Solutions

royalblues
Level 10
Level 10

Ypu would be required to use distribute lists for filtering routes from advertising.

The distribute-list can reference an access-list or prefix-list

eg. say R1<--->R2 R1 runs eigrp on all its interfaces but needs to send routing updates only for loopback1

R1

interface Loopback1

ip address 1.1.1.1 255.255.255.0

!

interface Loopback2

ip address 2.2.2.2 255.255.255.0

!

interface FastEthernet0/0

ip address 10.10.10.1 255.255.255.0

router eigrp 1

network 1.0.0.0

network 2.0.0.0

network 10.0.0.0

distribute-list prefix test out

no auto-summary

ip prefix-list test seq 10 permit 1.1.1.0/24

R2

interface FastEthernet0/0

ip address 10.10.10.2 255.255.255.0

router eigrp 1

network 10.0.0.0

no auto-summary

Router#sh ip route

Gateway of last resort is not set

1.0.0.0/24 is subnetted, 1 subnets

D 1.1.1.0 [90/156160] via 10.10.10.1, 00:06:50, FastEthernet0/0

10.0.0.0/24 is subnetted, 1 subnets

C 10.10.10.0 is directly connected, FastEthernet0/0

Router#

http://www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/1cfindep.html#wp1001343

HTH

Narayan

View solution in original post

3 Replies 3

royalblues
Level 10
Level 10

Ypu would be required to use distribute lists for filtering routes from advertising.

The distribute-list can reference an access-list or prefix-list

eg. say R1<--->R2 R1 runs eigrp on all its interfaces but needs to send routing updates only for loopback1

R1

interface Loopback1

ip address 1.1.1.1 255.255.255.0

!

interface Loopback2

ip address 2.2.2.2 255.255.255.0

!

interface FastEthernet0/0

ip address 10.10.10.1 255.255.255.0

router eigrp 1

network 1.0.0.0

network 2.0.0.0

network 10.0.0.0

distribute-list prefix test out

no auto-summary

ip prefix-list test seq 10 permit 1.1.1.0/24

R2

interface FastEthernet0/0

ip address 10.10.10.2 255.255.255.0

router eigrp 1

network 10.0.0.0

no auto-summary

Router#sh ip route

Gateway of last resort is not set

1.0.0.0/24 is subnetted, 1 subnets

D 1.1.1.0 [90/156160] via 10.10.10.1, 00:06:50, FastEthernet0/0

10.0.0.0/24 is subnetted, 1 subnets

C 10.10.10.0 is directly connected, FastEthernet0/0

Router#

http://www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/1cfindep.html#wp1001343

HTH

Narayan

Thank you, this is what I was looking for

johnlloyd_13
Level 9
Level 9

try using redistribute..as for route maps, it's mainly used for bgp (for policy based routing or PBR)

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco