Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Enabling NBAR for NAM

I have 6509 with WS-SVC-NAM-2 module. But I have difficulties to activate NBAR monitoring. My NAM Traffic Analyzer said that my software version incompatible. I have already check with Software Advisor tools, and my IOS have NBAR feature.

Here are my hardware info

IOS : s72033-adventerprisek9_wan-mz.122-18.SXF7.bin

Modules :

SFSwitch#sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 6 Firewall Module WS-SVC-FWM-1 SADXXXXXXXX

2 8 Intrusion Detection System WS-SVC-IDSM-2 SADXXXXXXXX

3 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SADXXXXXXXX

4 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SADXXXXXXXX

5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SADXXXXXXXX

7 8 Network Analysis Module WS-SVC-NAM-2 SADXXXXXXXX

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0019.2fa7.9a50 to 0019.2fa7.9a57 4.0 7.2(1) 3.1(3) Ok

2 0019.5670.df58 to 0019.5670.df5f 6.2 7.2(1) 5.0(2) Ok

3 0019.56c3.3220 to 0019.56c3.324f 2.5 12.2(14r)S5 12.2(18)SXF7 Ok

4 0019.55c5.18c0 to 0019.55c5.18ef 2.5 12.2(14r)S5 12.2(18)SXF7 Ok

5 0016.9df6.a138 to 0016.9df6.a13b 5.2 8.4(2) 12.2(18)SXF7 Ok

7 0019.561c.8082 to 0019.561c.8089 4.2 7.2(1) 3.5(1a) Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

2 IDS 2 accelerator board WS-SVC-IDSUPG SADXXXXXXXX 2.5 Ok

3 Centralized Forwarding Card WS-F6700-CFC SADXXXXXXXX 3.0 Ok

4 Centralized Forwarding Card WS-F6700-CFC SADXXXXXXXX 3.0 Ok

5 Policy Feature Card 3 WS-F6K-PFC3B SADXXXXXXXX 2.3 Ok

5 MSFC3 Daughterboard WS-SUP720 SADXXXXXXXX 2.5 Ok

Mod Online Diag Status

---- -------------------

1 Pass

2 Pass

3 Pass

4 Pass

5 Pass

7 Pass

Please help me how to activate this feature.

Thanks

Iwan

1 ACCEPTED SOLUTION

Accepted Solutions
Bronze

Re: Enabling NBAR for NAM

Network-Based Application Recognition (NBAR) for LAN ports is supported only with Supervisor Engine 2. With a sup720, only distributed NBAR on a flexwan is supported.

2 REPLIES
Bronze

Re: Enabling NBAR for NAM

Network-Based Application Recognition (NBAR) for LAN ports is supported only with Supervisor Engine 2. With a sup720, only distributed NBAR on a flexwan is supported.

New Member

Re: Enabling NBAR for NAM

IC, thanks for your explanation

284
Views
0
Helpful
2
Replies