Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

error detects on Gi3/8

Hi people,

I was getting errors on one of the switch port Gi3/8

And I verified the logs found it's relates mac-address mismatch.

MESSAGE INFO : Jun 26 20:11:43 GMT: %PM-SP-STDBY-4-ERR_DISABLE: link-flap error detected on Gi3/8, putting Gi3/8 in err-disable state

Jun 25 20:41:57 GMT: %DHCP_SNOOPING-5-DHCP_SNOOPING_MATCH_MAC_FAIL: DHCP_SNOOPING drop message because the chaddr doesn't match source mac, message type: DHCPRELEASE, chaddr: 001c.bf8b.9f05, MAC sa: 001c.2346.a21f

Jun 26 12:22:54 GMT: %DHCP_SNOOPING-5-DHCP_SNOOPING_MATCH_MAC_FAIL: DHCP_SNOOPING drop message because the chaddr doesn't match source mac, message type: DHCPREQUEST, chaddr: 001f.3c58.a62e, MAC sa: 001c.2355.8794

Jun 26 17:16:44 GMT: %DHCP_SNOOPING-5-DHCP_SNOOPING_MATCH_MAC_FAIL: DHCP_SNOOPING drop message because the chaddr doesn't match source mac, message type: DHCPREQUEST, chaddr: 001b.7767.73ab, MAC sa: 001c.2300.ee40

Jun 26 19:25:17 GMT: %DHCP_SNOOPING-5-DHCP_SNOOPING_MATCH_MAC_FAIL: DHCP_SNOOPING drop message because the chaddr doesn't match source mac, message type: DHCPREQUEST, chaddr: 0018.de99.bd06, MAC sa: 0018.8ba5.f726

Jun 26 20:04:41 GMT: %DHCP_SNOOPING-5-DHCP_SNOOPING_MATCH_MAC_FAIL: DHCP_SNOOPING drop message because the chaddr doesn't match source mac, message type: DHCPRELEASE, chaddr: 001c.bf8b.9f05, MAC sa: 001c.2346.a21f

Jun 26 20:11:43 GMT: %PM-SP-4-ERR_DISABLE: link-flap error detected on Gi3/8, putting Gi3/8 in err-disable state

Jun 26 20:11:43 GMT: %PM-SP-STDBY-4-ERR_DISABLE: link-flap error detected on Gi3/8, putting Gi3/8 in err-disable state

Jun 26 20:16:43 GMT: %PM-SP-4-ERR_RECOVER: Attempting to recover from link-flap err-disable state on Gi3/8

Jun 26 20:16:43 GMT: %PM-SP-STDBY-4-ERR_RECOVER: Attempting to recover from link-flap err-disable state on Gi3/8

Jun 26 20:18:03 GMT: %PM-SP-4-ERR_DISABLE: link-flap error detected on Gi3/8, putting Gi3/8 in err-disable state

Jun 26 20:18:03 GMT: %PM-SP-STDBY-4-ERR_DISABLE: link-flap error detected on Gi3/8, putting Gi3/8 in err-disable state

Jun 26 20:23:03 GMT: %PM-SP-4-ERR_RECOVER: Attempting to recover from link-flap err-disable state on Gi3/8

Jun 26 20:23:03 GMT: %PM-SP-STDBY-4-ERR_RECOVER: Attempting to recover from link-flap err-disable state on Gi3/8

Jun 26 20:24:42 GMT: %PM-SP-4-ERR_DISABLE: link-flap error detected on Gi3/8, putting Gi3/8 in err-disable state

Guys can somebody give quick response on this.

Regards,

Naidu.

2 REPLIES
Purple

Re: error detects on Gi3/8

Its exactly what it says the port is flapping . check for bad patches , house cable and speed/duplex mismatches, faulty nic card. The switch is temporarliy err-disabling port due to this condition.

New Member

Re: error detects on Gi3/8

Hi glen,

Thanks for the early reply.

Yes the port is flapping agreed is it cause by bad patches or duplex/speed mismatch or faulty nic?

jus small doubts here.

bad patches means patch cards am i right?

house cable means what?

faulty nic card in host or?

Thanks in advance.

Regards,

Naidu.

836
Views
0
Helpful
2
Replies