04-24-2010 02:01 PM - edited 03-06-2019 10:47 AM
hi all,
i did write erase and then did delete flash:vlan.dat after that i reloaded
when switch was booting up i get error
Error loading "flash:/c2950-i6k2l2q4-mz.121-22.EA8a.bin"
after this message switch booted ok
here is sh flash and other info
Switch#verify ?
/ios Verify compressed IOS image checksum
/md5 Compute an md5 signature for a file
flash: File to be verified
Switch#verify flash:/c2950-i6k2l2q4-mz.121-22.EA8a.bin
%Error verifying flash:/c2950-i6k2l2q4-mz.121-22.EA8a.bin (No such file or direc
tory)
Switch#sh flash:
Directory of flash:/
2 -rwx 3721946 Mar 01 1993 00:31:57 +00:00 c2950-i6k2l2q4-mz.121-22.E
A13.bin
7 -rwx 316 Oct 28 1993 05:57:54 +00:00 env_vars
21 -rwx 109 Mar 01 1993 00:04:19 +00:00 info
22 -rwx 109 Mar 01 1993 00:04:19 +00:00 info.ver
7741440 bytes total (4016640 bytes free)
my question is is everything ok with my switch?????????
many thanks
mahesh
Solved! Go to Solution.
04-24-2010 02:06 PM
mahesh18 wrote:
hi all,
i did write erase and then did delete flash:vlan.dat after that i reloaded
when switch was booting up i get error
Error loading "flash:/c2950-i6k2l2q4-mz.121-22.EA8a.bin"
after this message switch booted ok
here is sh flash and other info
Switch#sh flash:
Directory of flash:/
2 -rwx 3721946 Mar 01 1993 00:31:57 +00:00 c2950-i6k2l2q4-mz.121-22.E
A13.bin
7 -rwx 316 Oct 28 1993 05:57:54 +00:00 env_vars
21 -rwx 109 Mar 01 1993 00:04:19 +00:00 info
22 -rwx 109 Mar 01 1993 00:04:19 +00:00 info.ver7741440 bytes total (4016640 bytes free)
my question is is everything ok with my switch?????????
many thanks
mahesh
Mahesh
Your switch is trying to boot an image that isn't there. Perhaps you had a boot system ... statement in your running-config that pointed to EA13 image but when you deleted the running-config it fell back to the bootvar ?
Your switch is fine but i would suggest -
1) do a "sh version" and make sure the switch is using the EA13 image
2) add this to your config -
switch(config)# boot system flash flash:/c2950-i6k2l2q4-mz.121-22.EA13.bin
save the config and reload the switch and see if you still get the same error message.
Jon
04-24-2010 02:06 PM
mahesh18 wrote:
hi all,
i did write erase and then did delete flash:vlan.dat after that i reloaded
when switch was booting up i get error
Error loading "flash:/c2950-i6k2l2q4-mz.121-22.EA8a.bin"
after this message switch booted ok
here is sh flash and other info
Switch#sh flash:
Directory of flash:/
2 -rwx 3721946 Mar 01 1993 00:31:57 +00:00 c2950-i6k2l2q4-mz.121-22.E
A13.bin
7 -rwx 316 Oct 28 1993 05:57:54 +00:00 env_vars
21 -rwx 109 Mar 01 1993 00:04:19 +00:00 info
22 -rwx 109 Mar 01 1993 00:04:19 +00:00 info.ver7741440 bytes total (4016640 bytes free)
my question is is everything ok with my switch?????????
many thanks
mahesh
Mahesh
Your switch is trying to boot an image that isn't there. Perhaps you had a boot system ... statement in your running-config that pointed to EA13 image but when you deleted the running-config it fell back to the bootvar ?
Your switch is fine but i would suggest -
1) do a "sh version" and make sure the switch is using the EA13 image
2) add this to your config -
switch(config)# boot system flash flash:/c2950-i6k2l2q4-mz.121-22.EA13.bin
save the config and reload the switch and see if you still get the same error message.
Jon
04-24-2010 02:19 PM
Hi jon
I did exactly as you said and error is gone now.
Many thanks
best regards
mahesh
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: