Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Error message on ASR 1000 logs.

Hi Everyone,

 

Good day. 

 

I am seeing the below errors from the ASR 1000 that I have and It is not very clear on what the error actually means. 

If someone have had experience with this kind of similar error message, kindly assist: 

 

Apr 11 12:02:08.744 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:09.442 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:13.381 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:13.986 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:18.312 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:18.765 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:22.827 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:23.449 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:27.777 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:28.090 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:32.649 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:32.686 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:37.397 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:37.552 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:42.062 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:42.259 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:46.775 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:47.200 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:51.347 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:51.977 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:56.271 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:02:56.835 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:03:01.140 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:03:01.787 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:03:06.064 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:03:06.325 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:03:10.949 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:03:11.039 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:03:15.533 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0
Apr 11 12:03:15.858 AEST: ASR1000-INJECT: can't find tunnel adj for 0.0.0.0

 

Thanks

 

Kanes.R

 

  • LAN Switching and Routing
4 REPLIES
VIP Super Bronze

Hi,Are running any IPSEC/VPN

Hi,

Are running any IPSEC/VPN tunnel on this device?

New Member

Hi Rez, Yes DMVPN.

Hi Rez,

 

Yes DMVPN.

VIP Super Bronze

Hi,Ok, the message is

Hi,

Ok, the message is indicating that one of the tunnels can't find the adj device through default route (0.0.0.0)

Check your tunnels and make sure they are all working correctly and have peering. I am not sure if this is possible, but see if you can figure out if the tunnels have been running for some times or anyone of them flapping

HTH

New Member

Hi Reza, Thanks for the

Hi Reza,

 

Thanks for the update. However is there a specific way I can determine what is trying to establish a connection to the router and what is not? Based on the show DMVPN and so on I can see that the all of the tunnel has been up for over 5 weeks.

Thanks in advance. 

 

Regards,

 

Kanes.R

111
Views
0
Helpful
4
Replies