Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

error on catalyst 2950

C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)

Compiled Mon 22-Jul-02 17:18 by antonino

WS-C2950-24 starting...

Base ethernet MAC Address: 00:17:5a:1c:77:40

Xmodem file system is available.

Initializing Flash...

flashfs[0]: 373 files, 4 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 7741440

flashfs[0]: Bytes used: 4752384

flashfs[0]: Bytes available: 2989056

flashfs[0]: flashfs fsck took 7 seconds.

...done initializing flash.

Boot Sector Filesystem (bs:) installed, fsid: 3

Parameter Block Filesystem (pb:) installed, fsid: 4

Loading "flash:/c2950-i6q4l2-mz.121-22.EA6.bin"...#############################################################################################################################################################################################################

File "flash:/c2950-i6q4l2-mz.121-22.EA6.bin" uncompressed and installed, entry point: 0x80010000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Fri 21-Oct-05 01:59 by yenanh

Image text-base: 0x80010000, data-base: 0x80568000

Initializing flashfs...

flashfs[1]: 373 files, 4 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 7741440

flashfs[1]: Bytes used: 4752384

flashfs[1]: Bytes available: 2989056

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

Done initializing flashfs.

POST: System Board Test : Passed

POST: Ethernet Controller Test : Passed

ASIC Initialization Passed

%Error: initializing transceiver port Fa0/1

%Error: initializing transceiver port Fa0/2

%Error: initializing transceiver port Fa0/3

%Error: initializing transceiver port Fa0/4

%Error: initializing transceiver port Fa0/5

%Error: initializing transceiver port Fa0/6

%Error: initializing transceiver port Fa0/7

%Error: initializing transceiver port Fa0/8

%Error: initializing transceiver port Fa0/9

%Error: initializing transceiver port Fa0/10

%Error: initializing transceiver port Fa0/11

%Error: initializing transceiver port Fa0/12

%Error: initializing transceiver port Fa0/13

%Error: initializing transceiver port Fa0/14

%Error: initializing transceiver port Fa0/15

%Error: initializing transceiver port Fa0/16

%Error: initializing transceiver port Fa0/17

%Error: initializing transceiver port Fa0/18

%Error: initializing transceiver port Fa0/19

%Error: initializing transceiver port Fa0/20

%Error: initializing transceiver port Fa0/21

%Error: initializing transceiver port Fa0/22

%Error: initializing transceiver port Fa0/23

%Error: initializing transceiver port Fa0/24

how do i solve this big issue,is the switch bad or can be solved

5 REPLIES
Purple

Re: error on catalyst 2950

It's a hardware error and its failing post , time to RMA the box if you have a contract. If you have tried rebooting numerous times then get it replaced.

Hall of Fame Super Gold

Re: error on catalyst 2950

I'm with Glen. The 2950 can now be used as a door jam until you contact Cisco and get the appliance replaced.

Re: error on catalyst 2950

Are you getting any error messages AFTER the %Error: initializing?

Is there something such as:

POST set PHY loopback failed.strata_cmic_read_miim ERROR:

timeout (addr=0x00 id=0x0D)

If you let the switch on longer, does it have any other error messages or it reboots right after the initializing?

Community Member

Re: error on catalyst 2950

POST set PHY loopback failed.strata_cmic_read_miim ERROR:

timeout (addr=0x00 id=0x0D)

i have the above messages displayed,but didnt really notice it rebooting.i awiat ur quick response on next step.thanks

Community Member

Re: error on catalyst 2950

Hi Lavramov,

Please am waiting for update on this issue.i said the switch displays message u sent.

POST set PHY loopback failed.strata_cmic_read_miim ERROR:

timeout (addr=0x00 id=0x0D)

1226
Views
5
Helpful
5
Replies
CreatePlease to create content