Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Etherchannel 6148

Hi

As i seen i ciso documentation regaring etherchannel in 6148 Line card limited to 1 Gig ASCI

One more query if I configure ether channel with 2 6148 Linecard for example

CAT 1                                                     CAT 2

Module 3 Port 1------------------------Module 3 Port 1

Module 4 Port 1------------------------Module 4 Port 1

Whether this Ether channel port group will have 2 Gig ASCI or still its 1 Gig Limitation

Thanks

Vinu

3 REPLIES
Hall of Fame Super Silver

Re: Etherchannel 6148

Hello Vinoth,

clearly on each switch two different ASICs are involved.

this is also a good design for redundancy should a linecard fail the other member link would be up.

The only way to be sure that the 1Gbps + 1 Gbps are available is to not use ports served by the same ASIC chips.

in your case the grouping should be of 6 ports (not 8 ports I did a mistake in the other thread there is a 8 Gbps link to shared bus)

you should leave unused and shut ports 3/2-6 and 4/2-6.

Hope to help

Giuseppe

New Member

Re: Etherchannel 6148

Thanks for your reply

so we will use the 3/1 and 4/1 shutdown the remaining port 3/2-8 and 4/2-8

which means we will get 2 gig bandwidth ASCI for Etherchannel

is it 8 Gbps link to shared bus i seen its 8 port X 6 slot = 6 Gig

and also i posted some details to packet drop the belwo details says there

is some packet drop in that port

am i right

6506-SW-A#$ interface gigabitEthernet 4/11 | include qos3Outlost

53. qos3Outlost = 837682147

6506-SW-A#$ interface gigabitEthernet 4/12 | include qos3Outlost

53. qos3Outlost = 837682147

6506-SW-A#$ interface gigabitEthernet 4/13 | include qos3Outlost

53. qos3Outlost = 837682147

6506-SW-A#$ interface gigabitEthernet 4/14 | include qos3Outlost

53. qos3Outlost = 837682147

6506-SW-A#$ interface gigabitEthernet 4/15 | include qos3Outlost

53. qos3Outlost = 837682147

6506-SW-A#$ interface gigabitEthernet 4/16 | include qos3Outlost

53. qos3Outlost = 837682147

6506-SW-A#$ interface gigabitEthernet 4/17 | include qos3Outlost

53. qos3Outlost = 14694

6506-SW-A#$ interface gigabitEthernet 4/18 | include qos3Outlost

53. qos3Outlost = 14694

6506-SW-A#$ interface gigabitEthernet 4/19 | include qos3Outlost

53. qos3Outlost = 14694

6506-SW-A#$ interface gigabitEthernet 4/20 | include qos3Outlost

53. qos3Outlost = 14694

Thanks

Vinu

On Thu, Mar 25, 2010 at 12:54 PM, giuslar <

Hall of Fame Super Silver

Re: Etherchannel 6148

Hello Vinoth,

you are correct each ASIC handles 8 ports

>> On these modules there is a       single 1-Gigabit Ethernet uplink from the port ASIC that supports  eight ports.       These cards share a 1 Mb buffer between a group of ports (1-8, 9-16,  17-24,       25-32, 33-40, and 41-48)

as reported here

http://www.cisco.com/en/US//products/hw/switches/ps700/products_tech_note09186a00801751d7.shtml#ASIC

Hope to help

Giuseppe

307
Views
0
Helpful
3
Replies