Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

etherchannel between WS-C4506-E and stacked WS-C2960S-48LPS-L

Hello,

we are having a "suspend" issue to portchannels with 2960S switches only.

On our core switch we have the following setup:

interface Port-channel68
 description EC DELEJ02SAC88
 switchport
 switchport trunk allowed vlan 6,7,10-12,19-21,30,63
 switchport mode trunk
 

and the two ports are:

interface GigabitEthernet1/3/10
 description SAC88
 switchport trunk allowed vlan 6,7,10-12,19-21,30,63
 switchport mode trunk
 logging event link-status
 udld port aggressive
 channel-group 68 mode active

!
interface GigabitEthernet2/3/10
 description ECM DELEJ02SAC88-D20
 switchport trunk allowed vlan 6,7,10-12,19-21,30,63
 switchport mode trunk
 logging event link-status
 udld port aggressive
 channel-group 68 mode active

 

On the other end we have a stacked 2960s with two switches.

Ports are configured as this:

interface Port-channel1
 description Uplink Core
 switchport trunk allowed vlan 6,7,19,21
 switchport mode trunk

and the two stack ports (one of each switch):

!
interface GigabitEthernet1/0/49
 description Uplink Core/Chassis1
 switchport trunk allowed vlan 6,7,19,21
 switchport mode trunk
 udld port aggressive
 mls qos trust dscp
 channel-group 1 mode active

and

interface GigabitEthernet2/0/49
 description Uplink Core/Chassis2
 switchport trunk allowed vlan 6,7,19,21
 switchport mode trunk
 udld port aggressive
 mls qos trust dscp
 channel-group 1 mode active

Same configuration we do have on our not stacked 2960 and is working fine. But here we have one port in supended state:

Group  Port-channel  Protocol    Ports
------+-------------+-----------+-----------------------------------------------
1      Po1(SU)         LACP      Gi1/0/49(P) Gi2/0/49(s)

 

We don't have anything in the logs.

Do anybody came across with this issue or having nay idea how to fix it?

Many thanks in advance

@lex

 

 

 

 

 

 

4 REPLIES
Purple

   Verify your ports are

   Verify your ports are correct , you have different descr on the 4500 on the ports so i would verify they go where you think.  Trace them and or use CDP to verify they go where you think .  Config looks ok though i would match the allowed vlans on both sides to keep it consistent.  Look in the logs also , it usually gives an indication why it is suspending the ports.

New Member

I met similiar problem on

I met similiar problem on C4500.

Try to remove etherchannel configuration by taking ports to it's defaults and also interface Port-channel68.

Then create port channel interface by first issuing :

interface GigabitEthernet1/3/10
 description SAC88
 channel-group 68 mode active

!

interface GigabitEthernet2/3/10

  description ECM DELEJ02SAC88-D20
  channel-group 68 mode active

Then configure all stuff around switchport under interface Port-channel68.

Hi guys,thanks for quick

Hi guys,

thanks for quick respond. CDP neigh allready checked, connected to the right ports.

I will try removing / adding port channel on core but have to wait getting a time window from site.

 

THX

New Member

Did you get it worked?

Did you get it worked?

156
Views
0
Helpful
4
Replies