Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

%ETHPORT-5-IF_SEQ_ERROR

I am getting this error from Nexus 7K. What could it be?

2012 Feb 21 15:17:14 NX1-DataCenter %ETHPORT-5-IF_DOWN_ADMIN_DOWN: Interface Ethernet10/46 is down (

Administratively down)

2012 Feb 21 15:17:17 NX1-DataCenter %ETHPORT-5-IF_ADMIN_UP: Interface Ethernet10/46 is admin up .

2012 Feb 21 15:17:17 NX1-DataCenter %ETHPORT-5-IF_SEQ_ERROR: Error ("Connection timed out") communic

ating with MTS_SAP_PORT_CLIENT for opcode MTS_OPC_ETHPM_LCP_SET_PORT_CFG (RID_PORT: Ethernet10/46)

2012 Feb 21 15:17:17 NX1-DataCenter %ETHPORT-5-IF_DOWN_ERROR_DISABLED: Interface Ethernet10/46 is do

wn (Error disabled. Reason:Connection timed out)

2 REPLIES
New Member

%ETHPORT-5-IF_SEQ_ERROR

I also have this output:

Ethernet10/46 is down (Internal-Fail errDisable, (null): Connection timed out)

  Dedicated Interface

  Hardware: 1000 Ethernet, address: 4055.3924.2d42 (bia 30e4.dbef.b10d)

  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec

  reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA

  auto-duplex, 1000 Mb/s, media type is 1G

  Beacon is turned off

  Auto-Negotiation is turned on

  Input flow-control is off, output flow-control is off

  Rate mode is dedicated

  Switchport monitor is off

  EtherType is 0x8100

  Last link flapped 00:06:00

  Last clearing of "show interface" counters never

  30 seconds input rate 0 bits/sec, 0 packets/sec

  30 seconds output rate 0 bits/sec, 0 packets/sec

  Load-Interval #2: 5 minute (300 seconds)

    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps

  L3 in Switched:

    ucast: 0 pkts, 0 bytes - mcast: 0 pkts, 0 bytes

  L3 out Switched:

    ucast: 0 pkts, 0 bytes - mcast: 0 pkts, 0 bytes

  RX

    54814594 unicast packets  197 multicast packets  594676 broadcast packets

    55409467 input packets  9764736478 bytes

    0 jumbo packets  0 storm suppression packets

    0 runts  0 giants  0 CRC  0 no buffer

    0 input error  0 short frame  0 overrun   0 underrun  0 ignored

    0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop

    0 input with dribble  0 input discard

    0 Rx pause

  TX

    54175799 unicast packets  5020446 multicast packets  2696855 broadcast packets

    61893100 output packets  21446629890 bytes

    0 jumbo packets

    0 output error  0 collision  0 deferred  0 late collision

    0 lost carrier  0 no carrier  0 babble  0 output discard

    0 Tx pause

  6 interface resets

Cisco Employee

%ETHPORT-5-IF_SEQ_ERROR

Mohammed

I'd suggest you to contact TAC team. Message means that internal service "port-client" cannot reach the port for some reason.

HTH,

Alex

1727
Views
0
Helpful
2
Replies
CreatePlease to create content