cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2948
Views
0
Helpful
2
Replies

%ETHPORT-5-IF_SEQ_ERROR

Muhammed AKYUZ
Level 1
Level 1

I am getting this error from Nexus 7K. What could it be?

2012 Feb 21 15:17:14 NX1-DataCenter %ETHPORT-5-IF_DOWN_ADMIN_DOWN: Interface Ethernet10/46 is down (

Administratively down)

2012 Feb 21 15:17:17 NX1-DataCenter %ETHPORT-5-IF_ADMIN_UP: Interface Ethernet10/46 is admin up .

2012 Feb 21 15:17:17 NX1-DataCenter %ETHPORT-5-IF_SEQ_ERROR: Error ("Connection timed out") communic

ating with MTS_SAP_PORT_CLIENT for opcode MTS_OPC_ETHPM_LCP_SET_PORT_CFG (RID_PORT: Ethernet10/46)

2012 Feb 21 15:17:17 NX1-DataCenter %ETHPORT-5-IF_DOWN_ERROR_DISABLED: Interface Ethernet10/46 is do

wn (Error disabled. Reason:Connection timed out)

2 Replies 2

Muhammed AKYUZ
Level 1
Level 1

I also have this output:

Ethernet10/46 is down (Internal-Fail errDisable, (null): Connection timed out)

  Dedicated Interface

  Hardware: 1000 Ethernet, address: 4055.3924.2d42 (bia 30e4.dbef.b10d)

  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec

  reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA

  auto-duplex, 1000 Mb/s, media type is 1G

  Beacon is turned off

  Auto-Negotiation is turned on

  Input flow-control is off, output flow-control is off

  Rate mode is dedicated

  Switchport monitor is off

  EtherType is 0x8100

  Last link flapped 00:06:00

  Last clearing of "show interface" counters never

  30 seconds input rate 0 bits/sec, 0 packets/sec

  30 seconds output rate 0 bits/sec, 0 packets/sec

  Load-Interval #2: 5 minute (300 seconds)

    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps

  L3 in Switched:

    ucast: 0 pkts, 0 bytes - mcast: 0 pkts, 0 bytes

  L3 out Switched:

    ucast: 0 pkts, 0 bytes - mcast: 0 pkts, 0 bytes

  RX

    54814594 unicast packets  197 multicast packets  594676 broadcast packets

    55409467 input packets  9764736478 bytes

    0 jumbo packets  0 storm suppression packets

    0 runts  0 giants  0 CRC  0 no buffer

    0 input error  0 short frame  0 overrun   0 underrun  0 ignored

    0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop

    0 input with dribble  0 input discard

    0 Rx pause

  TX

    54175799 unicast packets  5020446 multicast packets  2696855 broadcast packets

    61893100 output packets  21446629890 bytes

    0 jumbo packets

    0 output error  0 collision  0 deferred  0 late collision

    0 lost carrier  0 no carrier  0 babble  0 output discard

    0 Tx pause

  6 interface resets

Oleksandr Nesterov
Cisco Employee
Cisco Employee

Mohammed

I'd suggest you to contact TAC team. Message means that internal service "port-client" cannot reach the port for some reason.

HTH,

Alex

Review Cisco Networking products for a $25 gift card