Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509 switch

Hi Team,

I am trying to setup WS-SVC-WISM2-K9 on cisco 6509 switch with IOS version 12.2(33)SXJ1.

I have completed the below config and seeing service-port up but not coming in oper-up status.

I have installed WiSM module in slot 8 and seeing TG8/1, T8/2,G8/3 and G8/4 switch ports under module 8.

I am seeing only the automatically created port-channel 415 up with only T8/1 in it which strange to me.

I cant modify those interfaces as seeing error " These interfaces can not be modified.

Please provide suggestion about wht could be the wrong here?

COR-01#sh wism status

Service Vlan : 93, Service IP Subnet : 1.1.1.1/255.255.255.0

      WLAN

Slot  Controller  Service IP       Management IP    SW Version    Controller Type    Status

----+-----------+----------------+----------------+------------+------------------+---------------

8     1           0.0.0.0          0.0.0.0                       WS-SVC-WISM-2-K9   Service Port Up

JP2-RDC-COR-01#sh wism module 8 controller 1 status

WiSM Controller 1 in Slot 8 configured with auto-lag

Operational Status of the Controller : Service Port Up

Service VLAN                         : 93

Service Port                         : 3

Service Port Mac Address             : 30e4.db38.9981

Service IP Address                   : 0.0.0.0

Management IP Address                : 0.0.0.0

Software Version                     :

Port Channel Number                  : 415

Allowed-vlan list                    : 90,800,810

Native VLAN ID                       : 90

WCP Keep Alive Missed                : 0

JP2-RDC-COR-01#sh module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL16084N3K

  2   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL16085AEH

  3   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL16159JHP

  4   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL16085099

  5    5  Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL1550Y2C7

  8    4  WiSM 2 WLAN Service Module             WS-SVC-WISM2-K9    SAL16159DWW

  9   16  CEF720 16 port 10GBaseT                WS-X6716-10T       SAL1626F9HR

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  c464.1305.b274 to c464.1305.b2a3   4.2   12.2(18r)S1  12.2(33)SXJ1 Ok

  2  c464.1387.f5b4 to c464.1387.f5e3   4.2   12.2(18r)S1  12.2(33)SXJ1 Ok

  3  5057.a866.6c98 to 5057.a866.6cc7   4.2   12.2(18r)S1  12.2(33)SXJ1 PwrDown

  4  f0f7.556a.2bc0 to f0f7.556a.2bef   4.2   12.2(18r)S1  12.2(33)SXJ1 PwrDown

  5  5475.d07b.62d0 to 5475.d07b.62d7   4.1   8.5(4)       12.2(33)SXJ1 Ok

  8  0007.7d8c.5390 to 0007.7d8c.539f   1.1   12.2(18r)S1  12.2(33)SXJ1 Ok

  9  442b.034f.7410 to 442b.034f.741f   2.1   12.2(18r)S1  12.2(33)SXJ1 Ok

TenGigabitEthernet8/1  unassigned      YES unset  up                    up

TenGigabitEthernet8/2  unassigned      YES unset  down                  down

GigabitEthernet8/3     unassigned      YES unset  up                    up

GigabitEthernet8/4     unassigned      YES unset  administratively down down

COR-01(config)#int g8/4

% This interface cannot be modified

Version 12.2(33)SXJ1

ip dhcp excluded-address 1.1.1.1

!

ip dhcp pool WiSM_service_Port

   host 1.1.1.2 255.255.255.0

   hardware-address 30e4.db38.a8c1

wism service-vlan 93

wism module 8 controller 1 allowed-vlan 90,800,810

wism module 8 controller 1 native-vlan 90

interface Vlan93

description WiSM service port do not route-Inner Chassis WiSM to Supervisor connection

ip address 1.1.1.1 255.255.255.0

COR-01#sh etherchannel summary

415    Po415(SU)        -        Te8/1(P)

7 REPLIES
Hall of Fame Super Gold

Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509 swit

Your Service Port VLAN (93) is NOT ALLOWED.  

New Member

Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509 swit

I have tried allowing vlan 93 but didnt work. I ahve run debug wism events on Cat6509 and seeing below logs:

Aug 17 02:44:26.035: WiSM-Evt:dman_show_module_status: Port Channel in the hwidb/fec goup is :1/415

Aug 17 02:44:26.799: WiSM-Evt:dman_cntrl_db_search_by_mac: Found mac 30e4.db38.9981 for slot/port 8/1
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp_added: cntrl 8/1 got an ip 1.1.1.3 30e4.db38.9981/30e4.db38.9981
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp: received a garp from 1.1.1.3/1.1.1.3
Aug 17 02:44:26.799: WiSM-Evt:dman_cntrl_db_search_by_mac: Found mac 30e4.db38.9981 for slot/port 8/1
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp_added: cntrl 8/1 got an ip 1.1.1.3 30e4.db38.9981/30e4.db38.9981

Aug 17 02:44:40.019: WiSM-Evt:dman_reg_arp: received a garp from 1.1.1.2/1.1.1.2

Aug 17 02:44:42.127: WiSM-Evt:dman_proc_keepalive_tmr_handler: keepalive timer expired for 8/1
Aug 17 02:44:42.127: WiSM-Evt:dman_cntrl_db_search: something wrong 15

WiSM Controller 1 in Slot 8 configured with auto-lag

Operational Status of the Controller : Started KeepAlive
Service VLAN                         : 93
Service Port                         : 3
Service Port Mac Address             : 30e4.db38.9981
Service IP Address                   : 1.1.1.3
Management IP Address                : 0.0.0.0
Software Version                     :
Port Channel Number                  : 415
Allowed-vlan list                    : 90,93,800,810
Native VLAN ID                       : 90
WCP Keep Alive Missed                : 0

Hall of Fame Super Gold

Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509 swit

Can you please post the output to the command "sh run | i wism module 8 controller 1"?

New Member

Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509 swit

COR-01#sh run | inc wism module 8 controller 1

wism module 8 controller 1 allowed-vlan 90,93,800,810

wism module 8 controller 1 native-vlan 90

Hall of Fame Super Gold

Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509 swit

Forgot to ask if you can also post the output to the command "sh wism module 8 controller 1 status".

New Member

Re: Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509

COR-01#sh wism module 8 controller 1 status

WiSM Controller 1 in Slot 8 configured with auto-lag

Operational Status of the Controller : Started KeepAlive
Service VLAN                         : 93
Service Port                         : 3
Service Port Mac Address             : 30e4.db38.9981
Service IP Address                   : 1.1.1.3
Management IP Address                : 0.0.0.0
Software Version                     :
Port Channel Number                  : 415
Allowed-vlan list                    : 90,93,800,810
Native VLAN ID                       : 90
WCP Keep Alive Missed                : 0

      

Also providing Controller interface summary output. I have not used DHCP here. Assigned static ips.

(Cisco Controller) >show interface summary

Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
management                       LAG  untagged 10.76.12.12     Static  Yes    No
service-port                     N/A  N/A      1.1.1.3         Static  No     No
virtual                          N/A  N/A      2.2.2.2         Static  No     No

Hall of Fame Super Gold

Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509 swit

I cant modify those interfaces as seeing error " These interfaces can not be modified.

You are not allowed to modify the etherchannel ports.  It's normal.

If you need to, you can only console into the WiSM 2 or you use the command to session in:  session slot 8 process 1

Command needs to be run in the 6500.

1784
Views
0
Helpful
7
Replies
CreatePlease login to create content