Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Finding Memory for Sup2 new IOS version

I'm trying to upgrade some old Sup 2's to a new version of IOS. However I need to know how much DRAM is on board to make sure I stay within the requirements (Already know I need a bigger flash card to store the image on).

Other than show ver (pasted below), which doesn't seem to show the right info from what I've read, is there a command to find the amount of DRAm in a sup2?

Thanks!

Cisco Internetwork Operating System Software

IOS (tm) c6sup2_rp Software (c6sup2_rp-DSV-M), Version 12.1(11b)E, EARLY DEPLOYM ENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Wed 27-Feb-02 09:08 by eaarmas

Image text-base: 0x40008980, data-base: 0x415B0000

ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)

BOOTLDR: c6sup2_rp Software (c6sup2_rp-DSV-M), Version 12.1(11b)E, EARLY DEPLOYM ENT RELEASE SOFTWARE (fc1)

hq-core uptime is 4 weeks, 6 days, 22 hours, 31 minutes

System returned to ROM by power-on (SP by power-on)

System restarted at 12:06:42 DST Mon May 4 2009

System image file is "bootflash:c6sup22-dsv-mz.121-11b.E.bin"

cisco Catalyst 6000 (R7000) processor with 227328K/34816K bytes of memory.

Processor board ID SAL06230U9D

R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

4 Virtual Ethernet/IEEE 802.3 interface(s)

144 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

381K bytes of non-volatile configuration memory.

16384K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

#show mod

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 XXXXXXXXXXX

7 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 XXXXXXXXXXX

8 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 XXXXXXXXXXX

9 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 XXXXXXXXXXX

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0009.1243.853c to 0009.1243.853d 3.7 6.1(3) 7.2(0.35) Ok

7 0003.6c27.a760 to 0003.6c27.a78f 1.4 5.4(2) 7.2(0.35) Ok

8 0003.6c2d.eaa0 to 0003.6c2d.eacf 1.4 5.4(2) 7.2(0.35) Ok

9 0003.6c27.5a20 to 0003.6c27.5a4f 1.4 5.4(2) 7.2(0.35) Ok

Mod Sub-Module Model Serial Hw Status

--- --------------------------- --------------- --------------- ------- -------

1 Policy Feature Card 2 WS-F6K-PFC2 XXXXXXXXXXX 3.2 Ok

1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 XXXXXXXXXXX 2.3 Ok

  • LAN Switching and Routing
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Bronze

Re: Finding Memory for Sup2 new IOS version

cisco Catalyst 6000 (R7000) processor with 227328K/34816K bytes of memory

You have 256MB DRAM.

Add the 2 numbers from the line above, remember the 1024 rule.

HTH,

__

Edison.

2 REPLIES
Hall of Fame Super Bronze

Re: Finding Memory for Sup2 new IOS version

cisco Catalyst 6000 (R7000) processor with 227328K/34816K bytes of memory

You have 256MB DRAM.

Add the 2 numbers from the line above, remember the 1024 rule.

HTH,

__

Edison.

New Member

Re: Finding Memory for Sup2 new IOS version

Thanks!

236
Views
0
Helpful
2
Replies