Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Flash problem

Recently I bought a FLASH memory; I tied replacing it with the FLASH mem I had.

The problem is, its not working...

rommon 15 > tftpdnld -r

IP_ADDRESS: 192.168.2.111

IP_SUBNET_MASK: 255.255.255.0

DEFAULT_GATEWAY: 192.168.2.1

TFTP_SERVER: 192.168.2.222

TFTP_FILE: c2600-i-mz123-26.bin

Receiving c2600-i-mz123-26.bin from 192.168.2.222 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

File reception completed.

program load complete, entry point: 0x80008000, size: 0x765238

Self decompressing the image : ############################################################################################################################# [OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

0000A2 0X00103980 C2600 Dual Fast Ethernet

0000CC 0X00179614 High Density Voice Port Module

0X00098670 public buffer pools

0X00211000 public particle pools

TOTAL: 0X00526604

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 6Mb.

Not enough memory in the system to run this image

Required pmem/iomem: 26934890/629145

*** System received a Software forced crash ***

signal= 0x17, code= 0x200, context= 0x80005f7c

PC = 0xffffffff, Vector = 0x200, SP = 0xffffffff

rommon 16 >

---------------------------------------------------------------------------------

If I dont use -r option, I get the result pretty fast,

rommon 8 > tftpdnld

IP_ADDRESS: 192.168.2.111

IP_SUBNET_MASK: 255.255.255.0

DEFAULT_GATEWAY: 192.168.2.1

TFTP_SERVER: 192.168.2.222

TFTP_FILE: c2600-i-mz123-26.bin

Invoke this command for disaster recovery only.

WARNING: all existing data in all partitions on flash will be lost!

Do you wish to continue? y/n: [n]: y

get_man_dev: Unknown device - probably NOT formatted.

unknown flash device - mandev code = 0xffff

cannot read flash info

TFTP: Error, insufficient flash installed to load image.

TFTP: Operation terminated.

rommon 9 >

-----------------------------------------------------------------------------------

rommon 16 > dir flash:

get_man_dev: Unknown device - probably NOT formatted.

unknown flash device - mandev code = 0xffff

cannot read flash info

getdevnum warning: device "flash" has size of zero

get_man_dev: Unknown device - probably NOT formatted.

unknown flash device - mandev code = 0xffff

cannot read flash info

getdevnum warning: device "flash" has size of zero

get_man_dev: Unknown device - probably NOT formatted.

unknown flash device - mandev code = 0xffff

cannot read flash info

getdevnum warning: device "flash" has size of zero

get_man_dev: Unknown device - probably NOT formatted.

unknown flash device - mandev code = 0xffff

cannot read flash info

getdevnum warning: device "flash" has size of zero

open: read error...requested 0x4 bytes, got 0x0

trouble reading device magic number

dir: cannot open device "flash:"

rommon 17 >

-------------------------------------------------------------------------------------

rommon 17 > meminfo

Main memory size: 24 MB.

Available main memory starts at 0x10000, size 24512KB

IO (packet) memory size: 25 percent of main memory.

NVRAM size: 32KB

rommon 18 >

Please try helpin me..!

Thanks,

Sylvester.

3 REPLIES
New Member

Re: Flash problem

http://cgi.ebay.com/NEW-BOOTROM-CISCO-2620-2621-MEM2620-32FSBOOT-BOOT-2600_W0QQitemZ380052757417QQcmdZViewItemQQptZCOMP_EN_Networking_Components?hash=item587ce8dba9&_trksid=p3286.m20.l1116

I think i will need to buy bootrom, else it doesnt recognise 32MB flash? Sounds rubblish,

Cisco 2600 Series Boot Rom MEM2620-32FSBOOT

Enable your Cisco 2620 and 2621 to recongize 32MB of Flash memory capacity

Part Number: MEM2620-32FSBOOT

Bootrom version 12.1(3r)T2

Currently im running -

System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

Copyright (c) 1999 by cisco Systems, Inc.

TAC:Home:SW:IOS:Specials for info

C2600 platform with 24576 Kbytes of main memory

New Member

Re: Flash problem

http://www.cisco.com/en/US/docs/routers/access/2600/hardware/installation/notes/262xboot.html

Incase anyone face the same problem, i think this can help. not sure unless some one confirms it.

Sylvester

Hall of Fame Super Gold

Re: Flash problem

Hi Sylvester,

This is one of the biggest pain to a 2600 router. You can't upgrade the bootstrap easily and require additional purchase and downtime. This was identified and starting from the 2691 onwards (3725/3745) you can now upgrade the bootstrap using software.

1030
Views
0
Helpful
3
Replies