Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Frame errors on 7513 fastethernet adapter

I have Cisco 7513 with fastethernet adapter PA-FE-TX connected to Catalyst WS-C2948. And i have permanent frame (and some time input) errors. Errors rate is block of about 22-30 errors each 10 seconds. I have disabled KeepAlive on router but C2948 don't have this option. I try to change cables but nothing change. How i can find problem?

Catalyst version:

WS-C2948 Software, Version NmpSW: 6.4(17)

Copyright (c) 1995-2005 by Cisco Systems, Inc.

NMP S/W compiled on Jun 2 2005, 18:49:54

GSP S/W compiled on Jun 02 2005, 14:16:48

System Bootstrap Version: 6.1(5)

Hardware Version: 2.4 Model: WS-C2948 Serial #: JAB05120BDF

Mod Port Model Serial # Versions

--- ---- ---------- -------------------- ---------------------------------

1 0 WS-X2948 JAB05120BDF Hw : 2.4

Gsp: 6.4(17.0)

Nmp: 6.4(17)

2 50 WS-C2948G JAB05120BDF Hw : 2.4

DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 65536K 31670K 33866K 12288K 5414K 6874K 480K 192K 288K

------------------------------

7513 version:

Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-JO3SV-M), Version 12.2(19a), RELEASE SOFTWARE (fc2)

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Tue 30-Sep-03 01:46 by pwade

Image text-base: 0x60010948, data-base: 0x6197E000

ROM: System Bootstrap, Version 11.1(8)CA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc

1)

BOOTLDR: RSP Software (RSP-BOOT-M), Version 12.2(19a), RELEASE SOFTWARE (fc2)

CALLOCALLROUTER uptime is 5 weeks, 1 day, 11 hours, 54 minutes

System returned to ROM by reload at 05:30:09 UTC Sun Oct 15 2006

System image file is "slot0:rsp-jo3sv-mz.122-19a.bin"

cisco RSP4 (R5000) processor with 262144K/2072K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

G.703/E1 software, Version 1.0.

G.703/JT2 software, Version 1.0.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

Bridging software.

TN3270 Emulation software.

Primary Rate ISDN software, Version 1.1.

Chassis Interface.

2 VIP2 R5K controllers (1 FastEthernet)(4 T1)(1 ATM).

1 FastEthernet/IEEE 802.3 interface(s)

4 Serial network interface(s)

1 ATM network interface(s)

123K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

8192K bytes of Flash internal SIMM (Sector size 256K).

Slave in slot 7 is running Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-DW-M), Version 12.2(19a), RELEASE SOFTWARE (fc2)

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Tue 30-Sep-03 01:50 by pwade

Slave: Loaded from system

Slave: cisco RSP4 (R5000) processor with 262144K bytes of memory.

Configuration register is 0x2102

2 REPLIES
Gold

Re: Frame errors on 7513 fastethernet adapter

Unless the hardware is bad you are more that likely getting collisions.

The PA_FE_TX card will only run at 100m. I have had lots of issues with these cards when I did not hard code both ends to 100 full duplex.

Since you replaced your cable there is not a lot left.

New Member

Re: Frame errors on 7513 fastethernet adapter

>The PA_FE_TX card will only run at 100m.

I have 15m only.

>I have had lots of issues with these cards when I did not hard code both ends to 100 full duplex.

I known this bug and always do it on interconnection cisco devices.

I founded that Catalyst have unresolved bug with keepalives from 7500 routers and it show this frames as error. But i have errors on router and i can't disable keepalives on Catalyst (Cisco bug ID CSCdr22809).

http://www.cisco.com/en/US/products/hw/switches/ps607/products_tech_note09186a0080125913.shtml

141
Views
0
Helpful
2
Replies
CreatePlease to create content