Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

frame relay circuit

Folks,

Can I have multipoint frame relay at the hub and point to point sub interfaces at the spoke? will it work?

6 REPLIES
Hall of Fame Super Bronze

Re: frame relay circuit

Yes, it will work.

Hub

Rack1R1#sh run int s1/0

Building configuration...

Current configuration : 242 bytes

!

interface Serial1/0

ip address 192.168.123.1 255.255.255.0

encapsulation frame-relay

serial restart-delay 0

frame-relay map ip 192.168.123.2 102 broadcast

frame-relay map ip 192.168.123.3 103 broadcast

no frame-relay inverse-arp

Spokes:

interface Serial1/0

no ip address

encapsulation frame-relay

serial restart-delay 0

!

interface Serial1/0.123 point-to-point

ip address 192.168.123.2 255.255.255.0

frame-relay interface-dlci 201

interface Serial1/0

no ip address

encapsulation frame-relay

serial restart-delay 0

!

interface Serial1/0.123 point-to-point

ip address 192.168.123.3 255.255.255.0

frame-relay interface-dlci 301

Verification:

Pinging from spoke to spoke

Rack1R3#ping 192.168.123.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.123.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 56/136/308 ms

Rack1R3#

Rack1R2#ping 192.168.123.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.123.3, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 48/112/220 ms

Rack1R2#

Pinging from hub to spokes:

Rack1R1#ping 192.168.123.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.123.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 20/60/140 ms

Rack1R1#ping 192.168.123.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.123.3, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 12/69/180 ms

Rack1R1#

HTH,

__

Edison.

New Member

Re: frame relay circuit

Edison,

Will this work if you had a multipoint subinterface at the hub instead of a physical interface?

Re: frame relay circuit

Hi

I think it doesnt make any difference if u r going with this setup.

Thanks

Mahmood

Re: frame relay circuit

You can work the way you want, only the L2 - L3 mappings should be perfect.

Hall of Fame Super Bronze

Re: frame relay circuit

multipoint subinterface has the same behavior as a physical main interface, the only difference is that you can have multiple multipoint subinterfaces while you can only have one physical interface.

HTH,

__

Edison.

Hall of Fame Super Bronze

Re: frame relay circuit

multipoint subinterface has the same behavior as a physical main interface, the only difference is that you can have multiple multipoint subinterfaces while you can only have one physical interface.

HTH,

__

Edison.

242
Views
0
Helpful
6
Replies