Hi to All,
please can you tell me what is the "FRU-power failed" ? It's a hardware problem on the module on the catalyst backplane or on the power-supply ?
Aug 28 08:48:03.079 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
Aug 28 08:48:03.111 MET-DST: %OIR-6-REMCARD: Card removed from slot 1, interfaces disabled
Aug 28 08:48:03.423 MET-DST: %MLSM-6-MMLS_MODE_CHANGE: MMLS: Replication Mode Change Detected because oir event
Aug 28 08:48:03.106 MET-DST: %C6KPWR-SP-4-DISABLED: power to module in slot 1 set off (Reset)
Aug 28 08:48:04.631 MET-DST: %BGP-5-ADJCHANGE: neighbor 82.98.12.xxx Down Interface flap
Aug 28 08:48:04.631 MET-DST: %BGP-5-ADJCHANGE: neighbor 82.98.12.xxx Down Interface flap
Aug 28 08:48:04.631 MET-DST: %BGP-5-ADJCHANGE: neighbor 82.98.12.xxx Down Interface flap
Aug 28 08:48:16.227 MET-DST: %OIR-SP-6-PWRFAILURE: Module 1 is being disabled due to power convertor failure
Aug 28 08:48:16.227 MET-DST: %C6KPWR-SP-4-DISABLED: power to module in slot 1 set off (FRU-power failed)
cisco#sh power
Load for five secs: 11%/0%; one minute: 7%; five minutes: 8%
Time source is NTP, 13:27:55.112 MET-DST Wed Sep 1 2010
system power redundancy mode = combined
system power total = 3885.00 Watts (92.50 Amps @ 42V)
system power used = 1774.50 Watts (42.25 Amps @ 42V)
system power available = 2110.50 Watts (50.25 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-2500W 2331.00 55.50 OK OK on
2 WS-CAC-2500W 2331.00 55.50 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 FAN-MOD-09 241.50 5.75 OK
2 FAN-MOD-09 241.50 5.75 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 OSM-4OC3-POS-SI+ 97.44 2.32 - - on off (FRU-power failed)
3 WS-X6704-10GE 402.36 9.58 402.36 9.58 on on
5 WS-SUP720-3BXL 328.44 7.82 328.44 7.82 on on
6 - - 328.44 7.82 - -
8 WS-X6724-SFP 232.26 5.53 232.26 5.53 on on
cisco#
cisco#sh env status
Load for five secs: 59%/3%; one minute: 10%; five minutes: 9%
Time source is NTP, 13:24:48.355 MET-DST Wed Sep 1 2010
backplane:
operating clock count: 2
operating VTT count: 3
fan-tray 1:
fan-tray 1 type: FAN-MOD-09
fan-tray 1 fan-fail: OK
fan-tray 2:
fan-tray 2 type: FAN-MOD-09
fan-tray 2 fan-fail: OK
VTT 1:
VTT 1 OK: OK
VTT 1 outlet temperature: 25C
VTT 2:
VTT 2 OK: OK
VTT 2 outlet temperature: 24C
VTT 3:
VTT 3 OK: OK
VTT 3 outlet temperature: 29C
clock 1:
clock 1 OK: OK, clock 1 clock-inuse: in-use
clock 2:
clock 2 OK: OK, clock 2 clock-inuse: not-in-use
power-supply 1:
power-supply 1 fan-fail: OK
power-supply 1 power-input: AC high
power-supply 1 power-output-fail: OK
power-supply 2:
power-supply 2 fan-fail: OK
power-supply 2 power-input: AC high
power-supply 2 power-output-fail: OK
module 3:
module 3 power-output-fail: OK
module 3 outlet temperature: 39C
module 3 inlet temperature: 24C
EARL 3 outlet temperature: 31C
EARL 3 inlet temperature: 29C
module 5:
module 5 power-output-fail: OK
module 5 outlet temperature: 28C
module 5 inlet temperature: 22C
module 5 device-1 temperature: 32C
module 5 device-2 temperature: 33C
module 5 asic-1 (SSO-1) temp: 21C
module 5 asic-2 (SSO-2) temp: 22C
module 5 asic-3 (SSO-3) temp: 22C
module 5 asic-4 (SSO-4) temp: 22C
module 5 asic-5 (SSA-1) temp: 22C
module 5 asic-6 (HYPERION-1) temp: 22C
RP 5 outlet temperature: 25C
RP 5 inlet temperature: 25C
EARL 5 outlet temperature: 31C
EARL 5 inlet temperature: 21C
module 8:
module 8 power-output-fail: OK
module 8 outlet temperature: 33C
module 8 inlet temperature: 24C
module 8 device-1 temperature: 24C
module 8 device-2 temperature: 29C
EARL 8 outlet temperature: 28C
EARL 8 inlet temperature: 28C
cisco#
Thanks,
Roberto Taccon
