Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

GSR 12008 error

Hello,

I have a GSR 12008 and I'm getting the below error message below and I've been unable to find a symptom/solution. Has anyone encountered this and is there a fix for this? Thanks.

Tim

00:03:19: %ENV_MON-4-ONEPEM: Only one PEM is available in GSR

4 REPLIES

Re: GSR 12008 error

HI,

Couldn't get a hit on error message decoder for this message..

Can you check whether you have any issues in the power entry modules on this GSR.

-VJ

New Member

Re: GSR 12008 error

Contador,

Do you have 1 or 2 power supplies installed? Did you lose one? You can perform a show env or sho hardware to investigate,'

Keep me posted,

rjh

New Member

Re: GSR 12008 error

I have one power supply installed (tried it in both slots, but got the same error) below ist he show env & sh hardware..

Router#show environment

Slot # Hot Sensor Inlet Sensor

(deg C) (deg C)

0 28.5 23.5

3 25.0 20.5

7 26.5 24.0

16 26.0 24.0

17 25.0 23.0

18 22.0 24.5

19 22.0 22.0

20 22.5 21.5

24 NA 27.0

Slot MBUS | CARD | PLIM Voltage Lines

# 5V | 3.3V 5.0V 2.5V | V3 V4 V5 V6 V7 V8

0 5056 3284 5008 - - - - - - -

3 5128 3288 4976 - - - - - - -

7 5120 3296 4992 2496 - - - - - -

16 5096 - - - - - - - - -

17 5104 - - - - - - - - -

18 5104 3288 - - - - - - - -

19 5096 3284 - - - - - - - -

20 5104 3308 - - - - - - - -

24 5104 - 5552 - - - - - - -

Slot # 5V MBUS 5V 48V AMP_48

(mv) (mv) (Volt) (Amp)

24 5552 5104 48 7

Slot # Fan Information

16 Voltage 25V Speed fast: Main Fans Ok Power Supply fans Ok

17 Voltage 25V Speed fast: Main Fans Ok Power Supply fans Ok

Slot # Card Specifc Leds

16 MBUS-OK

17 MBUS-OK

18 MBUS-OK

19 MBUS-OK

20 MBUS-OK

Router#show hardware

Cisco Internetwork Operating System Software

IOS (tm) GS Software (GSR-P-M), Version 12.0(31)S, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Sun 17-Apr-05 01:32 by kellythw

Image text-base: 0x50010F40, data-base: 0x54382000

ROM: System Bootstrap, Version 11.2(20030108:132517) [jkuzma-112 2.2] RELEASE SOFTWARE

BOOTLDR: GS Software (GSR-P-M), Version 12.0(31)S, RELEASE SOFTWARE (fc1)

Router uptime is 3 minutes

Uptime for this control processor is 3 minutes

System returned to ROM by reload at 16:28:47 UTC Mon Jan 8 2007

System image file is "slot0:gsr-p-mz.120-31.S.bin"

cisco 12008/GRP (R5000) processor (revision 0x01) with 262144K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

1 Route Processor Card

2 Clock Scheduler Cards

3 Switch Fabric Cards

1 four-port OC3 POS controller (4 POS).

1 six-port DS3 controller (6 DS3).

1 Ethernet/IEEE 802.3 interface(s)

4 Packet over SONET network interface(s)

507K bytes of non-volatile configuration memory.

32768K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

8192K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x2102

Router#

Re: GSR 12008 error

Hi,

The message that you see is not due to a error.

As you have only one PEM installed in the GSR, For informational purpose, It just reports that there is only one power supply installed in GSR.

Hoep this helps.

-VJ

446
Views
0
Helpful
4
Replies
CreatePlease to create content