Switching

Hello Community,I am looking a script for switches cisco for block interfaces with APs connected , the reason is because we receive daily port changes and sometimes the engineers change the vlan Wi-Fi by another and the Wi-Fi environment is affected ...

Hi thereI am assigned to check the issues with this attached network and have managed to remove some hups and redesign the network to what it is now. there were no vlans and it has been configured. the issue is that the internet speed is extremely sl...

Good day;Need help with how I can configure NAT overload with an existing vrf on a CAT9K_IOSXE V16.12.  This is what I am struggling with, I currently have a vrf called AWSDX-S3.  Now what I am trying to do is I have added a L2 SW and ran trunk ports...

hi friendsi config below commands to configure AAA authenticate with Microsoft Active Directory 2008(CIsco Device Integrate with AD microsoft for telnet and ssh and both can login to console by AD and local username) but while i unplugged Cisco Devic...

General question for the community.  I'm looking to use a Catalyst 9200 as my internet access switch.  Considering bumping my service from 1Gbps to at least 2Gbps and possibly higher.  Can the 9200 switch support higher than Gigabit throughput capaci...

Hi,I have a C9200L-48P switch with 4x1G uplink module.Port Gi1/1/1 does not have an LED blinking when connected to another switch.Ports Gi1/1/2-4 seem to work fine.Could anyone please guide me on troubleshooting the port and also advise action?  

Hi,I have a problem with stacking two cisco 9200L's, after stacking, one of the pair goes straight to privileged exec mode, without enable password, while the other needs password for it. It's not the first time, this occurs, do you have any idea whe...

Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1/1/2Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1...

Hi All,I came across a strange issue today. I have a C9300-48S-A Switch but the show version output of the switch shows that the switch has an Essentials license on it.Below snap for quick ref: Is this an error from Cisco or have I missed something?A...

I  wanted to test a local account on a Nexus switch and bypass the radius (ssh)connection. To do so, I add the  aaa authentication login default local  I am now able to access the local account but I wanna get back to the previous configuration. When...

Hi All - I purchased a CBS220-24t-4G switch a couple weeks back and have been unsuccessful at resolving these two issues. When starting up the switch after the system states Starting Kernel... I receive the following error: "unknown rt error f030". H...

Hi all I'm setting up a CISCO LAB to keep me busy in my retirement.  My Current network consists of a TP-Link Deco mesh network which works well for my IOT, PCs and internet access.  I just got hold of a Cisco 1941 router with a EHWIC D8SGP module.  ...

I have two 9410 switches connected in stackwise , when entering "show version" i can only see the primary stackwise member uptime. How can i see the uptime for the second member?

hello. I understand that Connected routing has an AD value of 0. The IP bands on the 1st and 2nd floors are different. 1st floor: 1.1.1.0/242nd floor: 2.2.2.0/24 There are two firewalls on top of the backbone. The band will be 3.3.3.0/24. If you conf...