HELP urgent - Install NM-1T3/E3 card in 3745

sam-lee · ‎06-04-2007

Hi,

I just installed NM-1T3/E3 in Cisco 3745. As my understanding, neither Cisco 3745 nor NM-1T3/E3 support OIR. So before i install the card, i power off the router. After i installed the card, i power on the router again. When I show ip int brief , i didnt see the card in the output. But when show diag, i saw the card was installed in slot 4. Can you anyone explain why this happened?

Thanks,

SAM

spremkumar · ‎06-04-2007

Hi SAM

Can you post the output of show version here ? and also Whats the ios version you are running out there ?

regds

sam-lee · ‎06-04-2007

Hi,

This is the output of show version

Cisco Internetwork Operating System Software

IOS (tm) 3700 Software (C3745-JS-M), Version 12.2(15)T16, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Tue 19-Apr-05 11:23 by ssearch

Image text-base: 0x60008954, data-base: 0x61E40000

ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

ROM: 3700 Software (C3745-JS-M), Version 12.2(15)T16, RELEASE SOFTWARE (fc2)

C3745 uptime is 2 days, 3 hours, 55 minutes

System returned to ROM by power-on

System restarted at 21:21:15 CST Sat Jun 2 2007

System image file is "flash:c3745-js-mz.122-15.T16.bin"

cisco 3745 (R7000) processor (revision 2.0) with 248832K/13312K bytes of memory.

Processor board ID JPE083330KV

R7000 CPU at 350Mhz, Implementation 39, Rev 3.3, 256KB L2, 2048KB L3 Cache

Bridging software.

X.25 software, Version 3.0.0.

TN3270 Emulation software.

2 FastEthernet/IEEE 802.3 interface(s)

8 Serial network interface(s)

1 ATM network interface(s)

1 Subrate T3/E3 ports(s)

DRAM configuration is 64 bits wide with parity disabled.

151K bytes of non-volatile configuration memory.

125184K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

Thanks,

SAM

mohammedmahmoud · ‎06-04-2007

Hi Sam,

You have to configure the channel-group under the controller for the serial interface to appear in the show ip interface brief. (the serial interface appears dynamically just after you configure the channel-group)

HTH, please do rate all helpful replies,

Mohammed Mahmoud.

sam-lee · ‎06-04-2007

Hi Mahammed,

Can you tell me how do configure the channel-group under the controller for the serial interface?

Thanks,

SAM

mohammedmahmoud · ‎06-04-2007

Hi SAM,

It should look something like this, but you'll need to consolidate the linecode, framing and time-slots with your provider:

controller e1

linecode {ami | hdb3}

framing {crc4 | no-crc4}

channel-group timeslots

After doing the above configuration, a serial interface with the same channel-number will be dynamically created, and its where you'll put the IPs and any other relevant configuration.

interface Serial

I hope that i've been informative.

HTH, please do rate all helpful replies using the scroll box on the right,

Mohammed Mahmoud.

sam-lee · ‎06-04-2007

Thanks both of you