Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

HELP urgent - Install NM-1T3/E3 card in 3745

Hi,

I just installed NM-1T3/E3 in Cisco 3745. As my understanding, neither Cisco 3745 nor NM-1T3/E3 support OIR. So before i install the card, i power off the router. After i installed the card, i power on the router again. When I show ip int brief , i didnt see the card in the output. But when show diag, i saw the card was installed in slot 4. Can you anyone explain why this happened?

Thanks,

SAM

6 REPLIES

Re: HELP urgent - Install NM-1T3/E3 card in 3745

Hi SAM

Can you post the output of show version here ? and also Whats the ios version you are running out there ?

regds

New Member

Re: HELP urgent - Install NM-1T3/E3 card in 3745

Hi,

This is the output of show version

Cisco Internetwork Operating System Software

IOS (tm) 3700 Software (C3745-JS-M), Version 12.2(15)T16, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Tue 19-Apr-05 11:23 by ssearch

Image text-base: 0x60008954, data-base: 0x61E40000

ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

ROM: 3700 Software (C3745-JS-M), Version 12.2(15)T16, RELEASE SOFTWARE (fc2)

C3745 uptime is 2 days, 3 hours, 55 minutes

System returned to ROM by power-on

System restarted at 21:21:15 CST Sat Jun 2 2007

System image file is "flash:c3745-js-mz.122-15.T16.bin"

cisco 3745 (R7000) processor (revision 2.0) with 248832K/13312K bytes of memory.

Processor board ID JPE083330KV

R7000 CPU at 350Mhz, Implementation 39, Rev 3.3, 256KB L2, 2048KB L3 Cache

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

TN3270 Emulation software.

2 FastEthernet/IEEE 802.3 interface(s)

8 Serial network interface(s)

1 ATM network interface(s)

1 Subrate T3/E3 ports(s)

DRAM configuration is 64 bits wide with parity disabled.

151K bytes of non-volatile configuration memory.

125184K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

Thanks,

SAM

Re: HELP urgent - Install NM-1T3/E3 card in 3745

Hi Sam,

You have to configure the channel-group under the controller for the serial interface to appear in the show ip interface brief. (the serial interface appears dynamically just after you configure the channel-group)

HTH, please do rate all helpful replies,

Mohammed Mahmoud.

New Member

Re: HELP urgent - Install NM-1T3/E3 card in 3745

Hi Mahammed,

Can you tell me how do configure the channel-group under the controller for the serial interface?

Thanks,

SAM

Re: HELP urgent - Install NM-1T3/E3 card in 3745

Hi SAM,

It should look something like this, but you'll need to consolidate the linecode, framing and time-slots with your provider:

controller e1

linecode {ami | hdb3}

framing {crc4 | no-crc4}

channel-group timeslots

After doing the above configuration, a serial interface with the same channel-number will be dynamically created, and its where you'll put the IPs and any other relevant configuration.

interface Serial

I hope that i've been informative.

HTH, please do rate all helpful replies using the scroll box on the right,

Mohammed Mahmoud.

New Member

Re: HELP urgent - Install NM-1T3/E3 card in 3745

Thanks both of you

435
Views
4
Helpful
6
Replies