cancel
Showing results forĀ 
Search instead forĀ 
Did you mean:Ā 
cancel
1362
Views
0
Helpful
14
Replies

Hi, I have a problem with iOS Version c3750e-ipbasek9-mz.122-58.SE2

IngMendoza22
Level 1
Level 1

Hi i need ur helps guys...

I have a problem, 2 switch with ios version c3750e-universalk9-mz.122-58.SE2.bin on stackwise. i cant work with route-map configuration, when i try to write anything command, the switch not accept.

whats version support this features...

Thxs

Julio Mendoza

---------------------------------------------------------------------------------------

SW01#sh ver

Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Thu 21-Jul-11 01:23 by prod_rel_team

ROM: Bootstrap program is C3750E boot loader

BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(58r)SE1, RELEASE SOFTWARE (fc1)

SW01 uptime is 6 hours, 10 minutes

System returned to ROM by power-on

System restarted at 07:38:11 Mexico Wed Nov 20 2013

System image file is "flash:/c3750e-universalk9-mz.122-58.SE2/c3750e-universalk9-mz.122-58.SE2.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

License Level: ipbase

License Type: Permanent

Next reload license Level: ipbase

cisco WS-C3750X-12S (PowerPC405) processor (revision K0) with 524288K bytes of memory.

Processor board ID FDO1727Z1YB

Last reset from power-on

19 Virtual Ethernet interfaces

1 FastEthernet interface

32 Gigabit Ethernet interfaces

4 Ten Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : 7C:69:F6:CE:05:80

Motherboard assembly number     : 73-13329-05

Motherboard serial number       : FDO17271UCC

Model revision number           : K0

Motherboard revision number     : C0

Model number                    : WS-C3750X-12S-S

Daughterboard assembly number   : 800-32727-03

Daughterboard serial number     : FDO17272018

System serial number            : FDO1727Z1YB

Top Assembly Part Number        : 800-35090-05

Top Assembly Revision Number    : E0

Version ID                      : V04

CLEI Code Number                : CMMFG00ARD

Hardware Board Revision Number  : 0x05

Switch Ports Model              SW Version            SW Image                

------ ----- -----              ----------            ----------              

*    1 18    WS-C3750X-12S      12.2(58)SE2           C3750E-UNIVERSALK9-M    

     2 18    WS-C3750X-12S      12.2(58)SE2           C3750E-UNIVERSALK9-M    

Switch 02

---------

Switch Uptime                   : 6 hours, 10 minutes

Base ethernet MAC Address       : 7C:69:F6:CE:13:80

Motherboard assembly number     : 73-13329-05

Motherboard serial number       : FDO17271UDC

Model revision number           : K0

Motherboard revision number     : C0

Model number                    : WS-C3750X-12S-S

Daughterboard assembly number   : 800-32727-03

Daughterboard serial number     : FDO17272007

System serial number            : FDO1727Z1XU

Top assembly part number        : 800-35090-05

Top assembly revision number    : E0

Version ID                      : V04

CLEI Code Number                : CMMFG00ARD

License Level                   : ipbase

License Type                    : Permanent

Next reboot licensing Level     : ipbase

Configuration register is 0xF

----------------------------------------------------------------------------------------

SW01#show license

Index 1 Feature: ipservices    

        Period left: 8  weeks 4  days

        License Type: Evaluation

        License State: Active, Not in Use, EULA not accepted

        License Priority: None

        License Count: Non-Counted

Index 2 Feature: ipbase        

        Period left: Life time

        License Type: Permanent

        License State: Active, In Use

        License Priority: Medium

        License Count: Non-Counted

14 Replies 14

Leo Laohoo
Hall of Fame
Hall of Fame

Index 1 Feature: ipservices

Period left: 8  weeks 4  days

License Type: Evaluation

Index 2 Feature: ipbase

Period left: Life time

License Type: Permanent

Maybe this is the reason why.  Your first switch is running an EVALUATION license of IP Services but your second switch is simply running IP Base.  I believe you need to enable IP Services on your second switch.

Jon Marshall
Hall of Fame
Hall of Fame

When you say route-map do you mean Policy Based Routing ? If so as Leo says you need IP Services for that. In addition you need to be running the routing template on your switches.

"sh sdm prefer"  shows which template you are running

"sdm prefer routing" changes to the routing template. You need to reload the switch before it takes effect.

Jon

is correct i need run PBR with interface vlans

i will check this informatiĆ³n.. and i will share the test

pls check this it.. i dont know..what i need, for run PBR wirh INTVLAN

i thing the version is the problem.. i need ipservices version...

SW01#show sdm prefer routing
"desktop routing" template:
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.

number of unicast mac addresses: 3K
number of IPv4 IGMP groups + multicast routes: 1K
number of IPv4 unicast routes: 11K
number of directly-connected IPv4 hosts: 3K
number of indirect IPv4 routes: 8K
number of IPv4 policy based routing aces: 0.5K
number of IPv4/MAC qos aces: 0.5K
number of IPv4/MAC security aces: 1K

thxs

Can you post output of "sdm prefer ?"

Jon

its the same

SW01#show sdm prefer

The current template is "desktop default" template.

The selected template optimizes the resources in

the switch to support this level of features for

8 routed interfaces and 1024 VLANs.

  number of unicast mac addresses:                  6K

  number of IPv4 IGMP groups + multicast routes:    1K

  number of IPv4 unicast routes:                    8K

    number of directly-connected IPv4 hosts:        6K

    number of indirect IPv4 routes:                 2K

  number of IPv4 policy based routing aces:         0

  number of IPv4/MAC qos aces:                      0.5K

  number of IPv4/MAC security aces:                 1K

thxs

Julio

That's not what i asked you to post. Can you enter the following command and post the output. I just want to check all the templates available -

SW01# sdm prefer ?

Jon

oki y try write "sdm prefer"

SW01#sdm prefer

                 ^

% Invalid input detected at '^' marker.

Did you add the question mark at the end - see previous post.

Jon

oky sorry u.u i understand bad

check this

SW01#sh sdm prefer ?

  access                          Access bias

  default                         Default bias

  dual-ipv4-and-ipv6              Support both IPv4 and IPv6

  indirect-ipv4-and-ipv6-routing  Supports more V4 and V6 Indirect Routes

  routing                         Unicast bias

  vlan                            VLAN bias

  |                               Output modifiers

 

Okay you need to change the template ie.

sdm prefer routing

you need to do this on all switches in the stack. And they will need reloading. But there is no point in doing this until your are running IP Services on all switches.

Once you have all the above you should be able to configure PBR.

Jon

thxs

whats is the command i need apply on all switches.. it is in configuration mode?

and how i check the template is the correct?

Thxs!

You need to apply the command on the stack master -

switch# sdm prefer routing

then reload and check with this command -

switch# sh sdm prefer

Jon

Julio

Just in case you need further info here is the 3750 config guide -

http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_55_se/configuration/guide/swsdm.html

Jon

Review Cisco Networking products for a $25 gift card