Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Host [MAC] vlan [x] is flapping between port [x/x/x] and port [x/x/x]

Hi all, I have two switches connected in cross-3750X stack into a single SW 6500., But I get the following error appears.

18w2d: %SW_MATM-4-MACFLAP_NOTIF: Host 0012.950a.9952 in vlan 10 is flapping between port Gi5/0/46 and port Gi6/0/44

What can i do?
Thank you very much¡¡.

 

 

6 REPLIES
Hall of Fame Super Gold

What is this machine with a

What is this machine with a MAC address of "0012.950a.9952"?  What is the configuration for ports Gi5/0/46 & Gi6/0/44?  

 

This error message is common when etherchannel is not configured properly at either ends.

New Member

forget the MAC this is a

forget the MAC this is a example.... on the attahcment you can see the error... yes maybe is a problem with etherchannel. 

 

SW6500-------------SW3750X(1)

            -------------SW3750(2)

             

is conexion among one 6500 and two 3705X. 

when i create the portchannel this issue appear.

 

 

Hall of Fame Super Gold

Are the two 3750 in a stack?

Are the two 3750 in a stack?

New Member

The configuration on the port

The configuration on the port channel is that all the port must be with the equal configuration :

For example :

interface Port-channel1
 description IDC-TO6500 - 192.168.0.12
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 1,54,136,192,432
 switchport mode trunk
 speed 100
 duplex full

interface GigabitEthernet1/0/1
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 1,54,136,192,432
 switchport mode trunk
 speed 100
 duplex full
 channel-protocol lacp
 channel-group 1 mode active
!
interface GigabitEthernet1/0/2
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 1,54,136,192,432
 switchport mode trunk
 speed 100
 duplex full
 channel-protocol lacp
 channel-group 1 mode active
!
 

The same configuration is on the 3750 :

 

interface Port-channel1
 description IDC-TO3750 - 192.168.0.12
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 1,54,136,192,432
 switchport mode trunk
 speed 100
 duplex full

interface GigabitEthernet1/0/1
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 1,54,136,192,432
 switchport mode trunk
 speed 100
 duplex full
 channel-protocol lacp
 channel-group 1 mode active
!
interface GigabitEthernet1/0/2
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 1,54,136,192,432
 switchport mode trunk
 speed 100
 duplex full
 channel-protocol lacp
 channel-group 1 mode active
!

New Member

yes, they are.¡

yes, they are.¡

HelloIf you know your

Hello

If you know your physical topology then somewhere between you switches you have a loop

show spanning-tree vlan 10

This will show you what ports are forwarding and its is also where you should discover what port shouldn't be in a forwarding state which is causing the stp loop

 

res

Paul

Please don't forget to rate any posts that have been helpful. Thanks.
3036
Views
20
Helpful
6
Replies
CreatePlease login to create content