cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
147068
Views
51
Helpful
9
Replies

How disable system message of Cisco Routers.

Hi Guys I´m new here, and I´m studying of CCNA in the Dominican Republic.

How can I disable systema message or alerts of a router or switch???

Example:

if i type: no shutdown in a interface display the following message or alert

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to upEste(config-if)#

or if after that I type end, the following message or alert appear:

%SYS-5-CONFIG_I: Configured from console by console

How can I disable this??? Help me!

Thank!

2 Accepted Solutions

Accepted Solutions

use this command in the global config mode

"no logging console"

View solution in original post

Ganesh Hariharan
VIP Alumni
VIP Alumni

Hi Guys I´m new here, and I´m studying of CCNA in the Dominican Republic.

How can I disable systema message or alerts of a router or switch???

Example:

if i type: no shutdown in a interface display the following message or alert

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to upEste(config-if)#

or if after that I type end, the following message or alert appear:

%SYS-5-CONFIG_I: Configured from console by console

How can I disable this??? Help me!

Thank!

Hi,

This command is quite straight forward and you’ll loose the ability to see what’s going on in the router/switch  while you are configuring. You might want to know when a network interface goes up or down, neighbor relationship formation, etc. So this is the least useful method, but you do not get any messages on your console.

no logging console

Check out the below link for more info:-

http://www.cisco.com/en/US/docs/ios/12_3/configfun/command/reference/cfr_1g04.html#wp1031439

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

View solution in original post

9 Replies 9

use this command in the global config mode

"no logging console"

When I am in switch configuration mode and typing the wrong command my console hung and when I am trying to use Ctrl +z it still taking more than 20 min time, could you please suggest me a command through which I will not get the error message and my console will not hang, as its getting hung and I am helpless at that time I am deleting the switch again and reinstall the configurations in Packet Tracer. Please see the attached screenshot for reference, 

 

no ip domain-lookup should end that issue.

Thank you Dhannanjoy Chowdhury!

Ganesh Hariharan
VIP Alumni
VIP Alumni

Hi Guys I´m new here, and I´m studying of CCNA in the Dominican Republic.

How can I disable systema message or alerts of a router or switch???

Example:

if i type: no shutdown in a interface display the following message or alert

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to upEste(config-if)#

or if after that I type end, the following message or alert appear:

%SYS-5-CONFIG_I: Configured from console by console

How can I disable this??? Help me!

Thank!

Hi,

This command is quite straight forward and you’ll loose the ability to see what’s going on in the router/switch  while you are configuring. You might want to know when a network interface goes up or down, neighbor relationship formation, etc. So this is the least useful method, but you do not get any messages on your console.

no logging console

Check out the below link for more info:-

http://www.cisco.com/en/US/docs/ios/12_3/configfun/command/reference/cfr_1g04.html#wp1031439

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

Hi Guys, thank for your answer that was what I was looking for.

Ganessh.iyer, I appreciated your recomendation but I´m not working in a real network, this is a practice that my teacher assigned me, is only a requeriment to complete the practice, in a real configuration I will try to no use.

Thank!

Jamesseibert11
Level 1
Level 1

Sorry to bump this ancient post, but it comes up at the top of google and I thought it was worth mentioning that maybe the original requester would have been happy with logging synchronous.

line con 0
 logging synchronous

luiztonello
Level 1
Level 1

Hello,

for this problems command "no macro auto global processing".

just practice this command in global configuration mode 

router(config)#no logging console 

 

 

 

 

best regards, 

 

Abdulrahman

AL-ATHWARI
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco