Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

How do i install a new IOS image in a Cisco Catalyst 2950? Error during the copy

Well, Starting from the beginning! i don´t know  what has happened with the  IOS that was originally installed in my switch 2950, i think it has been corrupted..So  when ever i try to console into my switch, instead of taking me to the  user mode i am getting a prompt that looked like this


Switch:

Later on i found out (thanks to Cisco's website)
  that it is because my  switch's IOS is either corrupted or missing and i download a  new IOS using fom the cisco page.. now whenever i try to copy this IOS image file,  using XMODEM, and even i try by transfer the image that i have stored on my PC, but I get an error message saying  that:


THE REMOTE OPERATOR IS NOT RESPONDING..

i'm using the Hyperterminal Private Edition!

even though now i have tried it for a number of times still i am getting  this error message does any one of you have any recommendation of how to avoid receiving this message or is there anyway in which i can copy  the IOS file to my switch's flash.. Please do let me know..

Everyone's tags (3)
6 REPLIES
VIP Super Bronze

Re: How do i install a new IOS image in a Cisco Catalyst 2950? E

Hi Jenny,

Can you login to the switch and use TFTP server to load the file into the flash instead if the Xmodem?  Xmodem takes a very long time to load the IOS into your switch.  With TFTF, since it is over Ethernet you can copy the file over the exiting one and it is pretty fast.

HTH

Reza

New Member

Re: How do i install a new IOS image in a Cisco Catalyst 2950? E

Hi Reza

My question is, didn´t exist other way to do that!?? someone told me that if i don´t have the ip adresses i can´t do it by tftp, got me? i mean what happened with the IOS?? and why i can´t install the new one, the switch is empty, when i use de dir flash: command it just apper this:

Directory of flash:/ 7740416 bytes available (1024 bytes used), just that, and i read about it in the cisco page in the article Recovering Catalyst Fixed Configuration Switches from a Corrupted or Missing Image say: If no Cisco IOS image files or image directories exist, you see that!

Hall of Fame Super Gold

Re: How do i install a new IOS image in a Cisco Catalyst 2950? E

Software Upgrade Procedure
http://www.cisco.com/en/US/customer/products/hw/routers/ps259/products_tech_note09186a00801fc986.shtml

Make sure you pay attention to the "Establish a Console Session with the Router" section.

Don't forget to rate useful posts.  Thanks.

Re: How do i install a new IOS image in a Cisco Catalyst 2950? E

Hi Reza

My question is, didn´t exist other way to do that!?? someone told me that if i don´t have the ip adresses i can´t do it by tftp, got me? i mean what happened with the IOS?? and why i can´t install the new one, the switch is empty, when i use de dir flash: command it just apper this:

Directory of flash:/ 7740416 bytes available (1024 bytes used), just that, and i read about it in the cisco page in the article Recovering Catalyst Fixed Configuration Switches from a Corrupted or Missing Image say: If no Cisco IOS image files or image directories exist, you see that!

Hi,

Check out the step by step procedure for ios upgarde for cisco 2950 switches

http://www.cisco.com/en/US/products/hw/switches/ps628/products_configuration_example09186a0080169627.shtml#configure2

Hope to Help !!

Ganesh.H

New Member

Re: How do i install a new IOS image in a Cisco Catalyst 2950? E

Hi

Check by changing the PC/Laptop

Silver

Re: How do i install a new IOS image in a Cisco Catalyst 2950? E

10835
Views
5
Helpful
6
Replies