Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

How to check High backplane utilization in 6500 switch

Hi all,

Is it tru that sh system command will sh us high backplane utilization in cisco 6500 switch???

6509-A> (enable) sh system

PS1-Status PS2-Status

---------- ----------

ok ok

Fan-Status Temp-Alarm Sys-Status Uptime d,h:m:s Logout

---------- ---------- ---------- -------------- ---------

ok off ok 891,14:49:54 12 min

PS1-Type PS2-Type

-------------------- --------------------

WS-CAC-1300W WS-CAC-1300W

Modem Baud Traffic Peak Peak-Time

------- ----- ------- ---- -------------------------

disable 9600 1% 22% Sat Oct 18 2008, 05:03:51

PS1 Capacity: 1153.32 Watts (27.46 Amps @42V)

PS2 Capacity: 1153.32 Watts (27.46 Amps @42V)

PS Configuration : PS1 and PS2 in Redundant Configuration.

System Name System Location System Contact CC

------------------------ ------------------------ ------------------------ ---

-6509-A

Core Dump Core File

------------------------ -------------------------------------------

disabled slot0:crashinfo

Crash Info Crash Info File

------------------------ -------------------------------------------

enabled bootflash:crashinfo

System Information Logging Host Interval

-------------------------- ---------------- --------

Disabled - 1440

System Information Log File

----------------------------------------------------------------------

tftp:sysinfo

Index System Information Logging Commands

----- ---------------------------------------------------------

Syslog Dump Syslog File

------------------------ -------------------------------------------

disabled

in this command which option shows backplane utilization????

many thanks

mahesh

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Blue

Re: How to check High backplane utilization in 6500 switch

8 REPLIES
Purple

Re: How to check High backplane utilization in 6500 switch

Yes that will show it . Also if its a 720 or 6500 with switch fabric module and fabric enable cards you can use show fabric utilization to see what is going on .

New Member

Re: How to check High backplane utilization in 6500 switch

Hi glen

thanks for reply

so this part of command shows backplane utilization

Modem Baud Traffic Peak Peak-Time

------- ----- ------- ---- -------------------------

disable 9600 1%>>>> 22% >>>>>>>>Sat Oct 18 2008, 05:03:51

Hall of Fame Super Blue

Re: How to check High backplane utilization in 6500 switch

New Member

Re: How to check High backplane utilization in 6500 switch

hi jon,

thanks one again

issue solved

many thanks

mahesh

New Member

Re: How to check High backplane utilization in 6500 switch

Hi,

I am running IOS 12.2(33)SXH2a on my 6509 switches and need to be able to see the backplane utilization. However, with IOS 12.2(33)SXH2a, I am not able to execute the "show system" or "show catalyst6000 traffic-meter" commands to backplane utilization.

CORE_1#sh catalyst6000 traffic-meter

This Supervisor hardware revision has no support for traffic meter feature.

CORE_1#sh system

^

% Invalid input detected at '^' marker.

What command can I use to display the backplane utilization for a 6509 running on IOS 12.2(33)SXH2a?

thx,

David

Hall of Fame Super Bronze

Re: How to check High backplane utilization in 6500 switch

New Member

Re: How to check High backplane utilization in 6500 switch

Edison,

That document solved my issue.

Thanks!

David

New Member

How to check High backplane utilization in 6500 switch

thanks to guide us how this issue solved .. what is the equivalent command on IOS to get utlization peaks ?

regards

7184
Views
5
Helpful
8
Replies
CreatePlease login to create content