11-05-2013 11:28 AM - edited 03-07-2019 04:26 PM
Hello there,
For some reason I messed up my home router and now I only have a CISCO 831 available and I would like to configure PPPoE on it and to use it as my home router from now on.
The question is that I don't know how to configure it, I found some useful links on the internet but everytime I tried to follow the steps, at some point, my router didn't had some of the options on the command line.
I, most likely, have a dynamic IP from my ISP and I use a username and a password to connect to internet.
Here is the start-up config that I have so far but don't know how to make it work, what should I do more to make it work over internet?
Using 971 out of 131072 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Home831
!
boot-start-marker
boot-end-marker
!
enable password XXXXXXXXXXX
!
no aaa new-model
!
resource policy
!
ip subnet-zero
!
!
ip cef
vpdn enable
!
!
!
!
!
!
!
!
!
bba-group pppoe global
!
!
interface Ethernet0
no ip address
shutdown
!
interface Ethernet1
no ip address
shutdown
duplex auto
!
interface Ethernet2
no ip address
shutdown
!
interface FastEthernet1
duplex auto
speed auto
!
interface FastEthernet2
duplex auto
speed auto
!
interface FastEthernet3
duplex auto
speed auto
!
interface FastEthernet4
duplex auto
speed auto
!
ip classless
ip http server
no ip http secure-server
!
!
!
control-plane
!
!
line con 0
password XXXXXXXXXXX
logging synchronous
login
no modem enable
line aux 0
line vty 0 4
password cisco
logging synchronous
login
!
scheduler max-task-time 5000
end
In case you need more info, please ask.
Cristian
11-05-2013 11:34 AM
Hi,
Use this link to configure:
http://www.cisco.com/en/US/tech/tk175/tk15/technologies_configuration_example09186a008071a729.shtml
follow this post:
https://supportforums.cisco.com/thread/188665
Regards
11-20-2013 11:56 PM
Hello,
I did that, followed the post, configured as follows but still cannot connect:
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname 831
!
logging queue-limit 100
!
ip subnet-zero
ip dhcp excluded-address 192.168.1.1
!
ip dhcp pool LOCALPOOL
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
!
ip audit notify log
ip audit po max-events 100
no ftp-server write-enable
!
interface Ethernet0
description Inside private interface
ip address 192.168.1.1 255.255.255.0
ip nat inside
hold-queue 100 out
!
interface Ethernet1
description Connection to DSL Modem ISP
no ip address
ip tcp adjust-mss 1452
load-interval 30
pppoe enable
pppoe-client dial-pool-number 1
no cdp enable
!
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp pap sent-username "my username without qotas" password 0 "my password without qotas"
!
ip nat inside source list 1 interface Dialer1 overload
ip classless
ip http server
no ip http secure-server
!
access-list 1 permit 192.168.1.0 0.0.0.255
!
ip route 0.0.0.0 0.0.0.0 Dialer1
dialer-list 1 protocol ip permit
!
line con 0
no modem enable
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
scheduler max-task-time 5000
!
end
What is wrong? Can you please tell me what I have to do more?
Thanks Cristian
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: