Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

How to "show" ME 3800 transceiver eeprom data?

z-core#show interfaces status

Port           Name             Status       Vlan         Duplex  Speed Type

Te0/1        R-CORE             connected    trunk        full    10G

Te0/2        M-CORE             notconnect   1            full    10G

As you can see Type feild is emty, so I'm unable to find out transeiver's type e.g. 10GBASE-LR, 10GBASE-ER and etc. How to look into it's eeprom data?

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

How to "show" ME 3800 transceiver eeprom data?

sh inventory

8 REPLIES
Hall of Fame Super Gold

How to "show" ME 3800 transceiver eeprom data?

Command:  sh idprom interface

New Member

How to "show" ME 3800 transceiver eeprom data?

Leo,

Thanks, there's no such command on ME3800:

z-core#show i? 

idb         identity   idmgr  if-mgr

interfaces  inventory  ip     ipam

ipc         ipv6       isis  

z-core#show ver

Cisco IOS Software, ME380x Software (ME380x-UNIVERSALK9-M), Version 15.2(4)S, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Fri 20-Jul-12 18:52 by prod_rel_team

Hall of Fame Super Gold

How to "show" ME 3800 transceiver eeprom data?

Darn.  I thought this command is supported.

How about "sh interface trans prop"?

New Member

Re: How to "show" ME 3800 transceiver eeprom data?

z-core#sh interface TenGigabitEthernet 0/1 transceiver properties

Name : Te0/1

Administrative Speed: 10000

Administrative Duplex: full

Administrative Auto-MDIX: on

Administrative Power Inline: N/A

Operational Speed: 10000

Operational Duplex: full

Operational Auto-MDIX: on

Media Type:

z-core#sh interface TenGigabitEthernet 0/2 transceiver ?     

  detail      Show interface transceiver detail

  properties  Show interface transceiver properties

  |           Output modifiers

 

The output shows something but not what we expected. Neither "detail" did (just DOM statistics) 

Hall of Fame Super Gold

How to "show" ME 3800 transceiver eeprom data?

sh inventory

New Member

Re: How to "show" ME 3800 transceiver eeprom data?

z-core#show inventory | begin "TenGigabitEthernet0/1"

NAME: "TenGigabitEthernet0/1", DESCR: ""

PID: SFP-10G-LR          , VID: V02 , SN: ECL150902DA    

NAME: "TenGigabitEthernet0/2", DESCR: ""

PID: SFP-10G-LR          , VID: V01 , SN: T12110975      

Hall of Fame Super Gold

How to "show" ME 3800 transceiver eeprom data?

LOL!

I should've used that first.  I thought you wanted MORE information than that.

Thanks for the ratings.

New Member

How to "show" ME 3800 transceiver eeprom data?

You are welcome. In this particular case all  I need to know is the transceiver's type which is preprogrammed into its eeprom. Probably ME3800 retrieves only basic info for 'sh inventory' and does not support to view all data.

632
Views
0
Helpful
8
Replies