Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

How to set up SPAN for a vlan Interface

Hi,

I am trying to capture traffic for a particular VLAN. I tried to do the following:

Torsaa-mls1(config)#monitor session 2 source interface vl

Torsaa-mls1(config)#monitor session 2 source interface vlan1

                                                       ^

% Invalid input detected at '^' marker.

.....

So VLAN are not supported. Is there any other way to accomplish this?

Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Blue

Re: How to set up SPAN for a vlan Interface

The 3560 does support vlans as the source. I think it may be your configuration ie. -

Torsaa-mls1(config)#monitor session 2 source interface vl

Torsaa-mls1(config)#monitor session 2 source interface vlan1

don't use the interface and vlan commands together. The command syntax is -

"monitor session source vlan "

Jon

4 REPLIES
Hall of Fame Super Blue

How to set up SPAN for a vlan Interface

It might help if you told us the switch model and IOS version

Jon

New Member

How to set up SPAN for a vlan Interface

There you go, SORRY!

Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(50)SE2, RELEASE SOFTWARE (fc2)

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Fri 15-May-09 22:11 by nachen

Image text-base: 0x00003000, data-base: 0x02400000

ROM: Bootstrap program is C3560E boot loader

BOOTLDR: C3560E Boot Loader (C3560E-HBOOT-M) Version 12.2(44r)SE3, RELEASE SOFTWARE (fc3)

Torsaa-mls1 uptime is 8 weeks, 4 days, 16 hours, 26 minutes

System returned to ROM by power-on

System image file is "flash:c3560e-universalk9-mz.122-50.SE2/c3560e-universalk9-mz.122-50.SE2.bin"

License Level: ipservices

License Type: Permanent

Next reload license Level: ipservices

cisco WS-C3560E-48TD (PowerPC405) processor (revision L0) with 122880K/8184K bytes of memory.

Processor board ID FDO1447Y1JL

Last reset from power-on

16 Virtual Ethernet interfaces

1 FastEthernet interface

52 Gigabit Ethernet interfaces

2 Ten Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : E0:5F:B9:3C:9E:00

Motherboard assembly number     : 73-11179-14

Motherboard serial number       : FDO14480AXG

Model revision number           : L0

Motherboard revision number     : A0

Model number                    : WS-C3560E-48TD-E

Daughterboard assembly number   : 800-29737-01

Daughterboard serial number     : FDO14470SUG

System serial number            : FDO1447Y1JL

Top Assembly Part Number        : 800-28930-04

Top Assembly Revision Number    : B0

Version ID                      : V05

CLEI Code Number                : COMCJ00ARB

Hardware Board Revision Number  : 0x00

Switch Ports Model              SW Version            SW Image

------ ----- -----              ----------            ----------

*    1 54    WS-C3560E-48TD     12.2(50)SE2           C3560E-UNIVERSALK9-M

Hall of Fame Super Blue

Re: How to set up SPAN for a vlan Interface

The 3560 does support vlans as the source. I think it may be your configuration ie. -

Torsaa-mls1(config)#monitor session 2 source interface vl

Torsaa-mls1(config)#monitor session 2 source interface vlan1

don't use the interface and vlan commands together. The command syntax is -

"monitor session source vlan "

Jon

New Member

How to set up SPAN for a vlan Interface

Thanks it worked, appreciat it.

132
Views
0
Helpful
4
Replies
CreatePlease to create content