Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

How to shutdown vlan in layer2

How to shutdown vlan in layer2 ? Thanks in advance.

I've done it using "shutdown" command. but still it is showing active in "show vlan".

switch0(config)#interface vlan 2
switch0(config-if)#
%LINK-5-CHANGED: Interface Vlan2, changed state to up

switch0(config-if)#shutdown


%LINK-5-CHANGED: Interface Vlan2, changed state to administratively down

switch0(config-if)#end
switch0#
%SYS-5-CONFIG_I: Configured from console by console

---------------------------

switch0#show vlan brief

VLAN Name                             Status    Ports

---- -------------------------------- --------- -------------------------------

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/6, Fa0/7, Fa0/8

                                                Fa0/9, Fa0/10, Fa0/11, Fa0/12

                                                Fa0/13, Fa0/14, Fa0/15, Fa0/16

                                                Fa0/17, Fa0/18, Fa0/19, Fa0/20

                                                Fa0/21, Fa0/22, Fa0/23, Fa0/24

                                                Gig1/1, Gig1/2

2    VLAN0002                         active   

Regards,

Chandu

Regards, Chandu
3 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Purple

How to shutdown vlan in layer2

HI Chandu,

vlan 100, shutdown, and  interface vlan 100, shutdown

Shutting down the interface  vlan 2 disables the Layer 3 interface for that VLAN on the switch.  This means hosts will still be able to communicate WITHIN the VLAN  (Layer 2) but can not be routed off of the subnet.

Shutting  down the VLAN (vlan 2) disables Layer 2 switching of that VLAN on the  switch. This will effectively turn off all layer 2 switching on the  VLAN (preventing all communication).

Regards

Dont forget to rate helpful posts.

VIP Purple

How to shutdown vlan in layer2

HI Chandu,

Are you using PT ????

PT dont have this command.

Thanks

VIP Purple

How to shutdown vlan in layer2

HI Chandu,

PT is more then enough for CCNA.

Dont worry just study the basic conecpts and do some lab practice on PT.

If you need any more labs then just PM me.

Regards

16 REPLIES
VIP Purple

How to shutdown vlan in layer2

HI Chandu,

vlan 100, shutdown, and  interface vlan 100, shutdown

Shutting down the interface  vlan 2 disables the Layer 3 interface for that VLAN on the switch.  This means hosts will still be able to communicate WITHIN the VLAN  (Layer 2) but can not be routed off of the subnet.

Shutting  down the VLAN (vlan 2) disables Layer 2 switching of that VLAN on the  switch. This will effectively turn off all layer 2 switching on the  VLAN (preventing all communication).

Regards

Dont forget to rate helpful posts.

Community Member

How to shutdown vlan in layer2

Sandeep,

I'm not seeing the any options here.

switch0(config)#vlan 2 ?

 

Regards,

Chandu

Regards, Chandu
VIP Purple

Re: How to shutdown vlan in layer2

Hi chandu,

Config t
Vlan 2
Shut

Regards


Sent from Cisco Technical Support iPhone App

Community Member

How to shutdown vlan in layer2

Still.

switch0(config)#vlan 2

switch0(config-vlan)#?

VLAN configuration commands:

  exit  Apply changes, bump revision number, and exit mode

  name  Ascii name of the VLAN

  no    Negate a command or set its defaults

switch0(config-vlan)#

Regards, Chandu
VIP Purple

How to shutdown vlan in layer2

HI Chandu,

Are you using PT ????

PT dont have this command.

Thanks

Community Member

How to shutdown vlan in layer2

Yes it's PT. Whenever i face this type situation na... then i'll doubt whether will PT help me to pass CCNA because it is not having these type of some basic commands..

And i can't get a real equipment...

Regards,

Chandu

Regards, Chandu
Community Member

How to shutdown vlan in layer2

Really sad...

But thanks for you help sandeep.

Regards, Chandu
VIP Purple

How to shutdown vlan in layer2

HI Chandu,

PT is more then enough for CCNA.

Dont worry just study the basic conecpts and do some lab practice on PT.

If you need any more labs then just PM me.

Regards

Community Member

How to shutdown vlan in layer2

HI,

Pls suspend the vlan

br/subhojit

Community Member

How to shutdown vlan in layer2

What is the command? Subhojit .

I think even that also will not be there in PT.

Regards, Chandu
VIP Purple

Re: How to shutdown vlan in layer2

No vlan 2

state command not supported on PT.

Regards

Sent from Cisco Technical Support iPhone App

Community Member

How to shutdown vlan in layer2

HI,

# Config t

vlan 111

state suspend

Br/Subhojit

Community Member

How to shutdown vlan in layer2

Same dialog. Not there.

However thank you both.

Regards, Chandu
Community Member

How to shutdown vlan in layer2

Thanks sandeep.

Regards,

Chandu

Regards, Chandu
Purple

Re: How to shutdown vlan in layer2

  If these commands don't show up its a packet tracer problem .  This is a known IOs command that's been around for many years.

conf t

vlan 10

shutdown

Community Member

How to shutdown vlan in layer2

There is no shutdown command here:

switch0(config-vlan)#?

VLAN configuration commands:

  exit  Apply changes, bump revision number, and exit mode

  name  Ascii name of the VLAN

  no    Negate a command or set its defaults

switch0(config-vlan)#

Regards, Chandu
591
Views
0
Helpful
16
Replies
CreatePlease to create content