Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Inactive interface on WS-C4507R+E

Hi,

I have a switch WS-C4507R + E, added two SFP SFP-10GBase-SR, and they stayed with inactive status, would like some help to activate these interfaces in 10Gb.

Tks

Eleandro

SWC-DC01#sh interfaces status module 4

Port      Name               Status       Vlan       Duplex  Speed Type

Te4/1                        connected    trunk        full a-1000 1000BaseBX10-U

Te4/2                        notconnect   1              full   auto No XCVR

Te4/3                        inactive        220           full   auto 10GBase-SR

Te4/4                        inactive        220           full   auto 10GBase-SR

SWC-DC01#sh ver

Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.02.02.SG RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 07-Dec-11 19:55 by prod_rel_team

|

|

cisco WS-C4507R+E (MPC8572) processor (revision 8) with 2097152K/20480K bytes of memory.

Processor board ID FOX1510H4QD

MPC8572 CPU at 1.5GHz, Supervisor 7

Last reset from Reload

15 Virtual Ethernet interfaces

96 Gigabit Ethernet interfaces

8 Ten Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.

SWC-DC01#sh module

Chassis Type : WS-C4507R+E

Power consumed by backplane : 40 Watts

Mod Ports Card Type                              Model              Serial No.

---+-----+--------------------------------------+------------------+-----------

1    48  10/100/1000BaseT (RJ45)                WS-X4648-RJ45-E    JAE15160DIT

2    48  10/100/1000BaseT (RJ45)                WS-X4648-RJ45-E    JAE15160DGE

3     4  Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1516L0G2

4     4  Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1516L0FU

SWC-DC01#sh inventory

NAME: "Linecard(slot 3)", DESCR: "Sup 7-E 10GE (SFP+), 1000BaseX (SFP) with 4 SFP+ Ports"

PID: WS-X45-SUP7-E     , VID: V01  , SN: CAT1516L0G2

NAME: "Linecard(slot 4)", DESCR: "Sup 7-E 10GE (SFP+), 1000BaseX (SFP) with 4 SFP+ Ports"

PID: WS-X45-SUP7-E     , VID: V01  , SN: CAT1516L0FU

NAME: "TenGigabitEthernet4/3", DESCR: "SFP-10Gbase-SR"

PID: SFP-10G-SR        , VID: V03  , SN: AGD162143P9

NAME: "TenGigabitEthernet4/4", DESCR: "SFP-10Gbase-SR"

PID: SFP-10G-SR        , VID: V03  , SN: AGD162143GN

SWC-DC01#sh run int te4/3

Building configuration...

Current configuration : 91 bytes

!

interface TenGigabitEthernet4/3

switchport access vlan 220

switchport mode access

end

SWC-DC01#sh run int te4/4

Building configuration...

Current configuration : 91 bytes

!

interface TenGigabitEthernet4/4

switchport access vlan 220

switchport mode access

end

SWC-DC01#sh int te4/3

TenGigabitEthernet4/3 is down, line protocol is down (inactive)

  Hardware is Ten Gigabit Ethernet Port, address is 6400.f159.bdc6 (bia 6400.f159.bdc6)

  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

  Full-duplex, Auto-speed, link type is auto, media type is 10GBase-SR

  input flow-control is off, output flow-control is off

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input never, output never, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     0 packets input, 0 bytes, 0 no buffer

     Received 0 broadcasts (0 multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 input packets with dribble condition detected

     0 packets output, 0 bytes, 0 underruns

     0 output errors, 0 collisions, 1 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier

     0 output buffer failures, 0 output buffers swapped out

SWC-DC01#sh int te4/4

TenGigabitEthernet4/4 is down, line protocol is down (inactive)

  Hardware is Ten Gigabit Ethernet Port, address is 6400.f159.bdc7 (bia 6400.f159.bdc7)

  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

  Full-duplex, Auto-speed, link type is auto, media type is 10GBase-SR

  input flow-control is off, output flow-control is off

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input never, output never, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     0 packets input, 0 bytes, 0 no buffer

     Received 0 broadcasts (0 multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 input packets with dribble condition detected

     0 packets output, 0 bytes, 0 underruns

     0 output errors, 0 collisions, 2 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier

     0 output buffer failures, 0 output buffers swapped out

SWC-DC01#sh int te4/3 transceiver detail

ITU Channel not available (Wavelength not available),

Transceiver is internally calibrated.

mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.

++ : high alarm, +  : high warning, -  : low warning, -- : low alarm.

A2D readouts (if they differ), are reported in parentheses.

The threshold values are calibrated.

                              High Alarm  High Warn  Low Warn   Low Alarm

          Temperature         Threshold   Threshold  Threshold  Threshold

Port       (Celsius)          (Celsius)   (Celsius)  (Celsius)  (Celsius)

--------- ------------------  ----------  ---------  ---------  ---------

Te4/3       21.5                75.0        70.0         0.0       -5.0

                              High Alarm  High Warn  Low Warn   Low Alarm

           Voltage            Threshold   Threshold  Threshold  Threshold

Port       (Volts)            (Volts)     (Volts)    (Volts)    (Volts)

---------  ---------------    ----------  ---------  ---------  ---------

Te4/3      3.26                  3.60        3.50        3.10       3.00

           Optical            High Alarm  High Warn  Low Warn   Low Alarm

           Transmit Power     Threshold   Threshold  Threshold  Threshold

Port       (dBm)              (dBm)       (dBm)      (dBm)      (dBm)

---------  -----------------  ----------  ---------  ---------  ---------

Te4/3      -40.0                 1.6        -1.3        -7.3      -11.3

           Optical            High Alarm  High Warn  Low Warn   Low Alarm

           Receive Power      Threshold   Threshold  Threshold  Threshold

Port       (dBm)              (dBm)       (dBm)      (dBm)      (dBm)

-------    -----------------  ----------  ---------  ---------  ---------

Te4/3      -40.0                 1.9        -1.0        -9.9      -13.9

SWC-DC01#sh int te4/4 transceiver detail

ITU Channel not available (Wavelength not available),

Transceiver is internally calibrated.

mA: milliamperes, dBm: decibels (milliwatts), NA or N/A: not applicable.

++ : high alarm, +  : high warning, -  : low warning, -- : low alarm.

A2D readouts (if they differ), are reported in parentheses.

The threshold values are calibrated.

                              High Alarm  High Warn  Low Warn   Low Alarm

          Temperature         Threshold   Threshold  Threshold  Threshold

Port       (Celsius)          (Celsius)   (Celsius)  (Celsius)  (Celsius)

--------- ------------------  ----------  ---------  ---------  ---------

Te4/4       23.2                75.0        70.0         0.0       -5.0

                              High Alarm  High Warn  Low Warn   Low Alarm

           Voltage            Threshold   Threshold  Threshold  Threshold

Port       (Volts)            (Volts)     (Volts)    (Volts)    (Volts)

---------  ---------------    ----------  ---------  ---------  ---------

Te4/4      3.29                  3.60        3.50        3.10       3.00

           Optical            High Alarm  High Warn  Low Warn   Low Alarm

           Transmit Power     Threshold   Threshold  Threshold  Threshold

Port       (dBm)              (dBm)       (dBm)      (dBm)      (dBm)

---------  -----------------  ----------  ---------  ---------  ---------

Te4/4      -40.0                 1.6        -1.3        -7.3      -11.3

           Optical            High Alarm  High Warn  Low Warn   Low Alarm

           Receive Power      Threshold   Threshold  Threshold  Threshold

Port       (dBm)              (dBm)       (dBm)      (dBm)      (dBm)

-------    -----------------  ----------  ---------  ---------  ---------

Te4/4       -4.8                 1.9        -1.0        -9.9      -13.9

SWC-DC01#sh int te4/3 capabilities

TenGigabitEthernet4/3

  Model:                 WS-X45-SUP7-E-Gbic

  Type:                  10GBase-SR

  Speed:                 1000,10000

  Duplex:                full

  Auto-MDIX:             no

  EEE:                   no

  Trunk encap. type:     802.1Q

  Trunk mode:            on,off,desirable,nonegotiate

  Channel:               yes

  Broadcast suppression: percentage(0-100), hw

  Multicast suppression: percentage(0-100), hw

  Flowcontrol:           rx-(off,on,desired),tx-(off,on,desired)

  VLAN Membership:       static, dynamic

  Fast Start:            yes

  CoS rewrite:           yes

  ToS rewrite:           yes

  Inline power:          no

  SPAN:                  source/destination

  UDLD:                  yes

  Link Debounce:         yes

  Link Debounce Time:    yes

  Port Security:         yes

  Dot1x:                 yes

  Maximum MTU:           9198 bytes (Jumbo Frames)

  Multiple Media Types:  no

  Diagnostic Monitoring: yes

SWC-DC01#sh int te4/4 capabilities

TenGigabitEthernet4/4

  Model:                 WS-X45-SUP7-E-Gbic

  Type:                  10GBase-SR

  Speed:                 1000,10000

  Duplex:                full

  Auto-MDIX:             no

  EEE:                   no

  Trunk encap. type:     802.1Q

  Trunk mode:            on,off,desirable,nonegotiate

  Channel:               yes

  Broadcast suppression: percentage(0-100), hw

  Multicast suppression: percentage(0-100), hw

  Flowcontrol:           rx-(off,on,desired),tx-(off,on,desired)

  VLAN Membership:       static, dynamic

  Fast Start:            yes

  CoS rewrite:           yes

  ToS rewrite:           yes

  Inline power:          no

  SPAN:                  source/destination

  UDLD:                  yes

  Link Debounce:         yes

  Link Debounce Time:    yes

  Port Security:         yes

  Dot1x:                 yes

  Maximum MTU:           9198 bytes (Jumbo Frames)

  Multiple Media Types:  no

  Diagnostic Monitoring: yes

SWC-DC01#sh redundancy

Redundant System Information :

------------------------------

       Available system uptime = 11 weeks, 6 days, 4 hours, 46 minutes

Switchovers system experienced = 1

              Standby failures = 0

        Last switchover reason = active unit failed

                 Hardware Mode = Duplex

    Configured Redundancy Mode = Stateful Switchover

     Operating Redundancy Mode = Stateful Switchover

              Maintenance Mode = Disabled

                Communications = Up

Current Processor Information :

------------------------------

               Active Location = slot 3

        Current Software state = ACTIVE

       Uptime in current state = 11 weeks, 6 days, 4 hours, 46 minutes

                 Image Version = Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.02.02.SG RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 07-Dec-11 19:55 by prod

               BOOT = bootflash:cat4500e-universalk9.SPA.03.02.02.SG.150-2.SG2.bin,1;

        Configuration register = 0x2102

Peer Processor Information :

------------------------------

              Standby Location = slot 4

        Current Software state = STANDBY HOT

       Uptime in current state = 4 weeks, 4 days, 21 hours, 58 minutes

                 Image Version = Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.02.02.SG RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 07-Dec-11 19:55 by pr

               BOOT = bootflash:cat4500e-universalk9.SPA.03.02.02.SG.150-2.SG2.bin,1;

        Configuration register = 0x2102

Everyone's tags (4)
1 REPLY
New Member

Inactive interface on WS-C4507R+E

(SOLVED)

I found the problem that occurred was using ports 3 and 4 as Cisco documentation in supervisory operating in redundant mode, ports 3 and 4 are inactivated. After changing to ports 1 and 2 were functioning without the need for custom configuration for 10Gb bandwith.

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/3.1.1SG/configuration/guide/sw_int.pdf

See 7-10

Limitation and Restriction on Supervisor Engine 7-E and Supervisor Engine 7L-E

Please note the following:


• When you use WS-X45-SUP-7-E in RPR or SSO mode, only the first two uplinks on each supervisor

engine are available. The second two uplinks are unavailable.

Selecting the Uplink Port on a Supervisor Engine 7L-E

Supervisor Engine 7L-E (WS-X45-SUP-7L-E) has two uplink modes: One-Gigabit and Ten-Gigabit.

The number of uplink ports now depends on the supervisor engine mode (single or redundandant) and

the uplink mode configuration (1-Gigabit or 10-Gigabit). To configure the uplink mode, use the

hw-module uplink select [gigabitethernet/ tengigabitethernet] command, as follows:

Switch(config)# hw-module uplink select ?

  gigabitethernet     Select the gigabit uplinks

  tengigabitethernet  Select the 10G uplinks

Note Supervisor Engine 7L-E  is not supported on a ten-slot chassis. USB device and SD card support is

applicable to both Supervisor Engine 7-E and Supervisor Engine 7L-E.

In general, observe the following:

• In Redundant Supervisor Mode, ports 3 and 4 on both supervisor engines are not usable.

• The total bandwidth of the connections on a Supervisor Engine 7-E is less than 48Gbps.

Tks for all!

11694
Views
5
Helpful
1
Replies
CreatePlease login to create content