Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Ingress/egress queuing on mpls interface.

Hi,

If am configuring COS based ingress/egress queuing on mpls interface, whether the line card/switch is able to see the COS marking on mpls packets or not. Line card is - WS-X6724-SFP.

Below are the configuration done under interface..

 
 wrr-queue bandwidth percent 5 25 15 35 20 0 0
 wrr-queue queue-limit 5 25 15 35 20 0 0
 wrr-queue threshold 1 80 1 1 1 1 1 1 1
 wrr-queue threshold 2 80 1 1 1 1 1 1 1
 wrr-queue threshold 3 80 1 1 1 1 1 1 1
 wrr-queue threshold 4 90 1 1 1 1 1 1 1
 wrr-queue threshold 5 100 1 1 1 1 1 1 1
 wrr-queue random-detect min-threshold 3 80 1 1 1 1 1 1 1
 wrr-queue random-detect min-threshold 4 90 1 1 1 1 1 1 1
 wrr-queue random-detect min-threshold 5 100 1 1 1 1 1 1 1
 wrr-queue random-detect max-threshold 3 100 1 1 1 1 1 1 1
 wrr-queue random-detect max-threshold 4 100 1 1 1 1 1 1 1
 wrr-queue random-detect max-threshold 5 100 1 1 1 1 1 1 1
 wrr-queue cos-map 2 1 1
 wrr-queue cos-map 3 1 2 6 7
 wrr-queue cos-map 4 1 3
 wrr-queue cos-map 5 1 4
 rcv-queue bandwidth percent 25 20 10 30 15 0 0 0
 rcv-queue queue-limit 40 20 20 10 10 0 0 0
 rcv-queue threshold 1 80 1 1 1 1 1 1 1
 rcv-queue threshold 2 80 1 1 1 1 1 1 1
 rcv-queue threshold 3 80 1 1 1 1 1 1 1
 rcv-queue threshold 4 90 1 1 1 1 1 1 1
 rcv-queue threshold 5 100 1 1 1 1 1 1 1
 rcv-queue threshold 6 100 1 1 1 1 1 1 1
 rcv-queue random-detect min-threshold 2 80 1 1 1 1 1 1 1
 rcv-queue random-detect min-threshold 3 80 1 1 1 1 1 1 1
 rcv-queue random-detect min-threshold 4 90 1 1 1 1 1 1 1
 rcv-queue random-detect min-threshold 5 100 1 1 1 1 1 1 1
 rcv-queue random-detect max-threshold 2 80 1 1 1 1 1 1 1
 rcv-queue random-detect max-threshold 3 100 1 1 1 1 1 1 1
 rcv-queue random-detect max-threshold 4 100 1 1 1 1 1 1 1
 rcv-queue random-detect max-threshold 5 100 1 1 1 1 1 1 1
 rcv-queue random-detect 2
 rcv-queue random-detect 3
 rcv-queue random-detect 4
 rcv-queue random-detect 5
 rcv-queue random-detect 6
 rcv-queue random-detect 7
 rcv-queue random-detect 8
 rcv-queue cos-map 1 1 0
 rcv-queue cos-map 2 1 1
 rcv-queue cos-map 3 1 2
 rcv-queue cos-map 4 1 3
 rcv-queue cos-map 5 1 4
 rcv-queue cos-map 6 1 5
 mls qos trust cos
 mpls ip

 

Regards,

Jofin 

 

 

1 REPLY
New Member

I could not quite get what

I could not quite get what you are asking but would refer you to the QOS design guide fro MPLS:

 

http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/WAN_and_MAN/QoS_SRND/QoS-SRND-Book/VPNQoS.html

152
Views
0
Helpful
1
Replies
CreatePlease to create content