Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Inject a global static route into a VRF table

Good morning,

I need to inject a static route into a VRF.

I have read i can add a static route adding global after the next hop.

I have done it but i can't ping.

Any solution ?

R1# ping 10.210.3.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.210.3.2, timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)

CS#       ping 10.210.3.10

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.210.3.10, timeout is 2 seconds:

.!!!!

Success rate is 80 percent (4/5), round-trip min/avg/max = 8/29/44 ms

CS#

CS#

CS#

*Mar  1 01:38:40.995: ICMP: echo reply rcvd, src 10.210.3.10, dst 10.210.3.2

*Mar  1 01:38:41.031: ICMP: echo reply rcvd, src 10.210.3.10, dst 10.210.3.2

*Mar  1 01:38:41.075: ICMP: echo reply rcvd, src 10.210.3.10, dst 10.210.3.2

*Mar  1 01:38:41.083: ICMP: echo reply rcvd, src 10.210.3.10, dst 10.210.3.2

CS#

if i add this static route on CS

CS(config)#ip route 192.168.0.0 255.255.255.252 192.168.0.6

and try to ping

CS#ping 192.168.0.1                                    

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:

U

*Mar  1 01:41:35.043: ICMP: dst (192.168.0.5) host unreachable rcv from 192.168.0.6.U

*Mar  1 01:41:37.047: ICMP: dst (192.168.0.5) host unreachable rcv from 192.168.0.6.U

Success rate is 0 percent (0/5)

CS#

*Mar  1 01:41:39.071: ICMP: dst (192.168.0.5) host unreachable rcv from 192.168.0.6

CS#

Everyone's tags (5)
1 ACCEPTED SOLUTION

Accepted Solutions

Re: Inject a global static route into a VRF table

Ciao Luca,

you definitely need a leak map. Essentially a route-map that leaks the route you need. Check for this reference on the internet / INE and you should find good example like this:

http://blog.ipexpert.com/2009/07/22/route-leaking-between-vrf-and-global-route-table/

or

http://www.cisco.com/en/US/tech/tk436/tk832/technologies_configuration_example09186a0080231a3e.shtml

or

http://www.gossamer-threads.com/lists/cisco/nsp/162584

Take Care

Alessio

2 REPLIES

Re: Inject a global static route into a VRF table

Ciao Luca,

you definitely need a leak map. Essentially a route-map that leaks the route you need. Check for this reference on the internet / INE and you should find good example like this:

http://blog.ipexpert.com/2009/07/22/route-leaking-between-vrf-and-global-route-table/

or

http://www.cisco.com/en/US/tech/tk436/tk832/technologies_configuration_example09186a0080231a3e.shtml

or

http://www.gossamer-threads.com/lists/cisco/nsp/162584

Take Care

Alessio

New Member

Inject a global static route into a VRF table

Thanks Alessio,

I have readed these solutions,

what do you mean saying to use routemap ?

1743
Views
0
Helpful
2
Replies
CreatePlease login to create content